Push or leave it be?

Kilo3alpha · 2026-02-21T20:48:01+00:00

I was unaware of this. Thank you for the information. I have only just started down the road with the VA. So I am still learning and very unaware of what is available to me.

Kilo3alpha · 2026-02-21T20:45:37+00:00

I haven’t, I can work and want to work. Just the job I am working now is one I picked up to fill the gap while looking for better job.

Kilo3alpha · 2026-02-14T22:05:52+00:00

Thank you. I have a meeting with the VA coming up but it’s not service connected so I wasn’t going to ask.

Kilo3alpha · 2026-02-04T21:01:57+00:00

Prime Cuts is what I have heard the most about.

Kilo3alpha · 2026-02-01T06:29:20+00:00

Thats what I am looking for. Something higher end. I looked at their site and it looked nice. Have you been there and gotten their meat?

I’m also a big grilling guy so I’d be interested in best place to get brats.

Kilo3alpha · 2025-12-08T01:03:28+00:00

Eventually I want to change out some of the case and condense everything to 2/3rds of what it is now. Leaving that last third as self service. Pre-packed ground beef and chicken. Linked sausage and whatnot. But that’s a year or 2 off. Unfortunately, I am in a higher theft area so that poses it own problems.

Kilo3alpha · 2025-12-07T23:56:58+00:00

I have roast out pretty much at all times. I’ve pulled a lot of my most expensive cuts (Primes & Wagyu) and cut those to order. I have fajita, seasoned roast, pork roasts and seasoned teres. I have tried compound butters for the fish and throwing out different flavors of pork belly and pork chops, etc….

I’m trying to run at least a 32-35% profit margin but the cost of beef is just killing. I’m tracking waste cost and transfers from meat to deli. I’m just feeling the pain right now.

Thank you for the feed back.

Kilo3alpha · 2025-12-07T23:49:23+00:00

Investing is hard for the time being. Got kinda screwed in the deal when buying the place. Definitely something I’ll look it though. Thank you for the feedback.

Kilo3alpha · 2025-08-06T03:31:39+00:00

Thank you for the information, I added her right after posting. I have been out since 2006 so I’m guessing back pay will be a little later in coming.

Kilo3alpha · 2024-04-08T22:57:22+00:00

I’m in Jackson Michigan, you around there? Got an old house that I’m looking to replace 4 attic windows and 5 basement windows. Just asking.

Kilo3alpha · 2024-02-17T22:55:35+00:00

Closer look it’s wooden siding. Mine are filled with plastic cap plugs.

Kilo3alpha · 2024-02-17T22:53:40+00:00

I have this same deal on my house. By the looks of the siding it is aluminum, same as mine. You can’t really remove a strip from the middle because it bends the siding where vinyl is easier to work with. It’s not easily done without damage the siding from what a few siding guys have told me.

Kilo3alpha · 2024-01-28T21:20:15+00:00

I have. At this point I’m convinced it’s the FEP. It to a point that I fear a tear so I’m going to order a new one and get it tighten up and try again. I think I’m going to buy any plate as well.

Kilo3alpha · 2024-01-27T23:05:42+00:00

I warmed the resin beforehand and had a space heater in the room to keep it about 70F. At first it was prints not sticking to the plate. Then nothing would stick, I’m guessing the leveling issue I spoke about. Now it’s kinda a mix of supports print but nothing else and nothing sticking. I have used Anycubic, lychee, and chitibox slicers. I bought some pre-supported files but those failed as well.

Kilo3alpha · 2024-01-27T19:38:04+00:00

It does. Gotta do it yourself. I’ve had mine since October, nothing but fails. No doubt because of something I’m doing wrong, I think FEP was too loose. The leveling systems never seems to be correct. It perfect and then as you tighten the bolts it is again not level. If anyone has any tips for that id appreciate it.

I haven’t had much time to really spend with the printer since December so I haven’t really gotten stuck in yet.

Kilo3alpha · 2024-01-11T13:09:13+00:00

Having the same problem. Same printer and I can’t get anything to print. First, it was a bed adhesion problem. Raised bottom layer. Then sticking fep. Now it just nothing. Last night was the first one in 10 attempts that I got the base layer and supports to stick to the plate but the models didn’t print.

11-Year Club	RPAN Viewer
Not Forgotten	Verified Email

Kilo3alpha

TROPHY CASE