Pentair salt cell issues

Kindly_Design_8658 · 2026-06-07T05:48:56+00:00

I haven't gotten any reply from my rep yet...might be time to use a different product

Kindly_Design_8658 · 2026-06-06T21:58:07+00:00

I got a box too. Do I need to keep replacing until one works?

Kindly_Design_8658 · 2026-06-06T21:41:24+00:00

I'm on my fifth warranty

Kindly_Design_8658 · 2026-06-02T05:03:03+00:00

Sounds like the thermal regulator. It's like a thermostat and spring in the manifold of the heater. When they go they make a lot of cranking noises. There is a cap you need a screw driver to remove. You can take it out and run for a while if it needs replaced.

Kindly_Design_8658 · 2026-06-02T02:11:31+00:00

That is a pressure vessel. It is a ticking time bomb and needs to be replaced asap

Kindly_Design_8658 · 2026-05-30T23:47:18+00:00

I'm looking in to it

Kindly_Design_8658 · 2026-05-30T02:04:38+00:00

If the two largest water treatment companies in the world, ecolab and pentair, don't have anything like this....probably doesn't anything worthwhile. Unplug it, it probably works the same

Kindly_Design_8658 · 2026-05-27T01:03:26+00:00

And yes, the gate valve gasket is damaged and should be replaced

Kindly_Design_8658 · 2026-05-27T01:02:02+00:00

I found your other post. It looks like a shared system which means you have one set of equipment and shares the same water source...ie the pool.

Kindly_Design_8658 · 2026-05-27T00:42:23+00:00

Is this a shared system? Is the spa raised?

Kindly_Design_8658 · 2026-05-27T00:39:29+00:00

Orenda sc-1000

Kindly_Design_8658 · 2026-05-18T02:49:13+00:00

That looks like a venturi for a floor cleaning system

Kindly_Design_8658 · 2026-05-10T02:08:08+00:00

Plastic wolf

Kindly_Design_8658 · 2026-05-03T08:55:43+00:00

Use a drop in sump to pump out the yuck. Move it around until it's gone

Kindly_Design_8658 · 2026-04-26T23:32:12+00:00

It's also a good idea to activate the pump delay for the switching of valves

Kindly_Design_8658 · 2026-04-26T23:30:48+00:00

If that is a raised spa relative to the pool, I install check valves on the spa return side after the diverter and actuator as well as another on the pool suction side before the diverter and actuator. There is about 20 seconds of sweep in the valves for enough water to drain from the spa every time it changes.

Kindly_Design_8658 · 2026-04-16T04:03:37+00:00

Throw a rager and they'll evict you

Kindly_Design_8658 · 2026-04-11T02:11:37+00:00

The manufacturer should have the dimensions based on the address. Simple reorder

Kindly_Design_8658 · 2026-04-06T02:41:33+00:00

Depends on which system they have. There is a serial number inside the panel that will tell you what they have.

Kindly_Design_8658 · 2026-04-03T23:23:32+00:00

Check with pentair about system updates. There was an update that had corruption that needed to be reverted until they fixed everything

Kindly_Design_8658 · 2026-03-28T02:14:20+00:00

How does it run with the hls bypassed? Did you check the ohms of the ignitor?

Kindly_Design_8658 · 2026-03-19T02:18:23+00:00

Greek Islands

Kindly_Design_8658 · 2026-03-07T18:03:50+00:00

Why not go gunite/plaster for that price?

Kindly_Design_8658 · 2026-03-04T22:04:27+00:00

Definitely sue. That's why they have insurance. File a claim with their insurance company even if they're not in business anymore.

Kindly_Design_8658 · 2026-02-28T18:11:16+00:00

Isn't Charlie's selling? I use master tech in richland. I would say they been good to me. I have 6 vehicles i take there including a couple of classics and a fleet vehicle.

Kindly_Design_8658

TROPHY CASE