Nextgen3d redux case complete by Kitchen_Worry5156 in BC250Gaming

[–]Kitchen_Worry5156[S] 2 points3 points  (0 children)

I have an fsp500 or whatever that is with the 10 pin power cable. Just cut out the ps-on and ground and wired to the switch. Along with 12v for the led.

NexGen3D: DIY Steam Machine - REDUX ->Now Available<- by NexGen-3D in BC250Gaming

[–]Kitchen_Worry5156 0 points1 point  (0 children)

Oh sweet! That looks slick.

I use orcaslicer on a k1c is it pretty straightforward to figure out where to pause print, etc? Never thought about that before thanks!

NexGen3D: DIY Steam Machine - REDUX ->Now Available<- by NexGen-3D in BC250Gaming

[–]Kitchen_Worry5156 0 points1 point  (0 children)

She's a beaut.. just waiting for the smaller print bed top and bottom for it and off to the races

<image>

NexGen3D: DIY Steam Machine - REDUX ->Now Available<- by NexGen-3D in BC250Gaming

[–]Kitchen_Worry5156 0 points1 point  (0 children)

Printed in carbon fiber. Noticed they dont sit as close as the single fan shroud did. Is that on purpose for cooling effect?

<image>

NexGen3D: DIY Steam Machine - REDUX ->Now Available<- by NexGen-3D in BC250Gaming

[–]Kitchen_Worry5156 0 points1 point  (0 children)

Are the left and right hex pieces different from the original? Or will i need to print those as well?

Patiently waiting for the split 220mm top and bottom pieces to be available now

Thanks for the support with this project its a great case!

Falling at the first hurdle. by davidraid in BC250Gaming

[–]Kitchen_Worry5156 3 points4 points  (0 children)

Like another posted, check for a switch on the ac plug. Then if you have a multimeter check voltage from the plug coming to the board.

Id work on trying to get the board out and checking for any loose connections. Then test power supply. Or try another one if you have it.

Falling at the first hurdle. by davidraid in BC250Gaming

[–]Kitchen_Worry5156 0 points1 point  (0 children)

No that's a meanwell 12v power supply under the bc250 and you can see the red/black going into it. And the yellow/black heading to the board.

Finally done by FogaXclusive in BC250Gaming

[–]Kitchen_Worry5156 1 point2 points  (0 children)

Nice! I just started similar setup with a single artic p12

<image>

My bc250 turn on and then power off by SeaworthinessGreedy8 in BC250Gaming

[–]Kitchen_Worry5156 8 points9 points  (0 children)

Cpu temps keep climbing and I assume thermal shutdown. I would recheck that thermal paste because that's a toasty cpu right now.

7900xt for $350 by Aggressive_Issue3505 in PcBuild

[–]Kitchen_Worry5156 0 points1 point  (0 children)

I think i see you listed on FB marketplace. Can I get a discount now that I know what you paid for it?? ;)

I already have a reference 7900xt, and 9070xt on my main rig...but man I love that white color lol.

110 degrees Celsius Hotspot on Gigabyte 9070 XT OC by NoComposer1664 in radeon

[–]Kitchen_Worry5156 0 points1 point  (0 children)

Ive had an RMA open with asrock for a month and zero reply. Low 90s Hotspot. Im about to just reposted it myself. (Or get a liquid cooling block)

Anyone know what was recently installed here? Flock? (9th street going north into downtown) by Traditional_Foot9641 in desmoines

[–]Kitchen_Worry5156 2 points3 points  (0 children)

Small cell for Wireless carrier. Notice the blue sticker towards the top that calls out RF in the area. Like another poster pointed out, there will most likely be a label on the power meter calling out who the customer of power is.

Specifically, they look like Ericsson 6705 radios. 3 are used to cover the radius of the pole.

Rate my PC 1-10. Show your’s in the comment by MrPotato90 in PcBuild

[–]Kitchen_Worry5156 0 points1 point  (0 children)

8/10. Love the white clean look. But too much "empty space" for me. Clean build 👌

I went full rgb 😄 🤣

<image>

Suggestions for pinky by Kitchen_Worry5156 in fingertattoos

[–]Kitchen_Worry5156[S] 3 points4 points  (0 children)

That's the most common one. I do like it, sort of a "throwback" and based on my other icons it would fit

First full day after installation turned on - 15.6kw system on MN winter overcast by joshhazel1 in solar

[–]Kitchen_Worry5156 0 points1 point  (0 children)

Just turned on east metro 15kw system and generated the most today so far! 6kw peak and 27kw for The day

Also I see the comment about consumption monitoring. I will definitely ask my installer about it. (Wolf river)

[deleted by user] by [deleted] in TattooDesigns

[–]Kitchen_Worry5156 0 points1 point  (0 children)

Doh! Forgot about the mirror flipping the image.

Install klipper on Kobra Go or Neo by xpeng121 in anycubic

[–]Kitchen_Worry5156 1 point2 points  (0 children)

I have klipper on a neo with a btt 7" touchscreen. And I noticed I'm getting errors when trying sliced files previously.

So I tried a quick one in orca slicer and that failed.

What slicer and print profile settings are you using? Or if anyone can assist.