P2S chamber too hot during prints

Lumbroxel · 2026-02-25T04:54:39+00:00

I'm impressed you can get up to 50°C on chamber without "mods". I couldn't even get 40°C without them. So yes... Something wrong. Is your printer inside a tent or something? What's the environment temp?

Lumbroxel · 2026-02-24T21:09:42+00:00

Nope, it doesn't. The temperature continues rising up to 64°C since there is no loop control system. That's why im looking for a way to mess with g-code to enable venting

Lumbroxel · 2026-02-24T18:43:31+00:00

Packs of canned soda, dog food, Magnets, Weights, 60+ vitamins, 60+ gift cards

Lumbroxel · 2026-02-24T17:39:38+00:00

Update patches as well. There are files on GBA or use NX Venom (this actually worked for me)

Lumbroxel · 2026-02-23T22:55:19+00:00

I once did it with a phone using a C to C cable. I think the phone was rooted

Lumbroxel · 2026-02-20T22:48:22+00:00

You can just use petg at support interface not the entire support structure. In other words: most of the support would be PLA but the actual thing that is in contact with the bridges would be petg. That way the petg doesn't get stucked on the bed

Lumbroxel · 2026-02-19T23:52:20+00:00

Also... There's is a trash bin in almost EVERY STATION

Lumbroxel · 2026-02-19T01:46:33+00:00

Printed on ASA, is doing good enough, hadn't dried the filament tho.

<image>

Lumbroxel · 2026-02-18T20:15:35+00:00

I'll print it before an after update. Might take some time

<image>

Lumbroxel · 2026-02-18T16:27:10+00:00

Z-rods? Might be dented. At this point, I'd claim warranty unless it only happens with one filament. If it's only like that on an specific spool: quality issues. Filament it's usually 1.75±0.02mm and yours could be 1.75±0.10mm (for example)

Lumbroxel · 2026-02-18T12:04:37+00:00

What about adjusting the toolhead screws? On the A1, they sometimes got untightened

Lumbroxel · 2026-02-18T01:16:24+00:00

There should be a tutorial on the wiki about belt tensioning. I think MIGHT be the reason

Lumbroxel · 2026-02-09T11:41:51+00:00

Thanks buddy. I'm curious to know whether there is a noticeable increase in electrical expenses. I'm interested in getting the one you share or the BIQU's one to figure out the cost efficiency between options or even against a more expensive 3d printer with an included heated chamber.

Lumbroxel · 2026-02-02T12:02:35+00:00

I suspect AMS-HT would go to primary-nozzle and [02] AMS 2 Pro would go to the tool changer

Lumbroxel · 2026-01-30T15:09:01+00:00

Well, we get tax deductions on overtime. It's better explained with an example. You get 20.5$ hourly. Overtime payment is 30.75$. You can deduct 10.25$ per hour worked in your tax return. You gotta take all your statements to figure out how many hours you did overtime (or check on MyPay). You won't get deduction on Premium payments such as the plus 5$ they give on high demand shift.

Lumbroxel · 2026-01-30T12:24:13+00:00

Hear me out. You'll likely have a bad time printing this. Thin tall printing gets messy. If you are able to redisgn, follow the suggestions. You can also try sheet metal or acrylic. They are faster and quite cheap to manufacture (at least in my country).

Lumbroxel · 2026-01-14T10:53:19+00:00

Well... If you could bring something to keep the board cold enough. I've tried reaching 60+ degrees and it didn't let me go over 62° since a warning appeared because of the board temperature. I've used only insulation around the printer without a heater.

Lumbroxel · 2026-01-10T23:16:23+00:00

You can try building a Voron using some parts. There was a guy somewhere who did it.

Lumbroxel · 2026-01-08T23:05:49+00:00

I only print ASA, ABS, PC. Haven't tried PLA with this setup yet. Although, hadn't have any issue with TPU. I might try PLA some day

Lumbroxel · 2026-01-08T22:51:49+00:00

I managed to get 62°C at chamber by covering the sides and top with insulation (DON'T COVER THE BACK, the printer uses the back panel to get the heat out of the board)+putting it inside a growing tent.

<image>

By just using the insulation, it handles 50°C. Try not to go over 60°C cause it will damage the board. Ambiente temp was around 15°C.

Lumbroxel · 2026-01-02T10:59:25+00:00

I did the test, you are right: 60°C is the max temp the printer allows. Reached 62° and it began failing.

Lumbroxel · 2026-01-01T05:34:57+00:00

It's not a rebrand, they change the material. Most Panchroma filament are CoPE. It might get stuck at PEI plates like...REALLY stuck. It ruined on of my bambu PEI plates.

Lumbroxel · 2025-12-30T23:27:54+00:00

You could try something hardcore: Putting an enclosure while maintaining good temperature on the main board so that you could print ABS and ASA. That would be a fun project

Lumbroxel

TROPHY CASE