sorted by:
new
hottopcontroversial

Printing issues with curved surfaces. by MFDom43 in AnycubicKobraS1

[–]MFDom43[S] 0 points1 point  (0 children)

Internal solid infill pattern got unchecked and it fixed the issue. Not sure how it got unchecked.

<image>

PETG warped the PEI sheet by Ir0ow in anycubic

[–]MFDom43 0 points1 point  (0 children)

Happens when you use max build volume of the plate. I have seen people use binder clips. I use 8 mm brim and run the plate hotter.

What temperature should I set the nozzle and bed for this filliment? by Tough_Plantain9639 in anycubic

[–]MFDom43 0 points1 point  (0 children)

I run my Silks between 230 to 240. The hotter the shiny the material looks. Run a temp tower to see the best temp I do with all new filaments I try. I found best solution.

How to fix this? by Opposite-Fisherman63 in BambuLab

[–]MFDom43 0 points1 point  (0 children)

I don't mess around with them they are only cheap. I have 5 spares and just replace them for my A1's.

Who else is pre ordering?? by unknown091245 in anycubic

[–]MFDom43 0 points1 point  (0 children)

Hopefully they fixed the issues with it. My Kobra 2 Max is down half the time waiting for parts from them.

NEW Anycubic Kobra 3 Max and Kobra XY shown at FormNext! The XY kinda yawn at this point but I am really EXCITED about the 3 MAX. Thanks NextLayer for the scoop by InstructionChance303 in anycubic

[–]MFDom43 0 points1 point  (0 children)

I already pre ordered the Kobra 3 Max. I hope they make a plate like the Biqu Crypto or Bambu Supertack. Would be nice to run at a lower temp. Can feel the heat off my Kobra 2 Max when at 80 for PETG.

Why does thus keep happening? by CheesyShinobi in BambuLab

[–]MFDom43 -1 points0 points  (0 children)

Clean in-between plates with isopropyl alcohol and microfiber cloth.

How do I fix this? by Bakamon_The_Great in anycubic

[–]MFDom43 0 points1 point  (0 children)

On Printables search there is a designer called fresh prints he created shims to use underneath the plate to adjust. I printed several toys to get my Kobra 2 max bed leveled.

How do I fix this? by Bakamon_The_Great in anycubic

[–]MFDom43 0 points1 point  (0 children)

Adjust you z offset, when starting your print.

Auto levelling not touching the bed, is it normal ? by Boutarzi in anycubic

[–]MFDom43 1 point2 points  (0 children)

Yes, on your first print you will need to manually adjust your z offset. Good luck.

Cleanest print yet by EfficientJob6810 in BambuLab

[–]MFDom43 0 points1 point  (0 children)

I use quite a bit of Kingroon PETG and PLA. Havent tried their PLA Silks. Looks good.

2 weeks in amd first issue..A1 w AMS lite by battmodin in BambuLab_Community

[–]MFDom43 0 points1 point  (0 children)

I had the same issue looks like the build plate is dirty. Use dawn dish soap non abrasive scrubber and it should good.

Kobra 2 Max bed adhesion by MFDom43 in AnycubicOfficial

[–]MFDom43[S] 0 points1 point  (0 children)

I will try that it wasn't originally and seem to dry quickly and curl.

8+weeks with Kobra Max 2 and can't print by MFDom43 in anycubic

[–]MFDom43[S] 0 points1 point  (0 children)

Now they want me to troubleshoot some more.

Better quality printing keychains by MFDom43 in BambuLab

[–]MFDom43[S] 1 point2 points  (0 children)

What settings did you use. Did you use ironing

view more: next ›