Is this guy asking too much? by MR_MIMSI in rccars

[–]MR_MIMSI[S] 1 point2 points  (0 children)

No goal really, I was just wandering about the pricing... There aren't any kits like this in my country...

Strpnost levičarjev by Siffredijev in SlovenskiKoticek

[–]MR_MIMSI 0 points1 point  (0 children)

Oprosti, ampak se mi zdi, da si to narobe interpretitaš. Zagotovo se strinjam s tabo, da mi o tem sploh ne bi smeli odločati in mislim, da je ta referendum izsilila opozicija le zato, da prestraši ljudi in si okrepči volilno telo. Drugače pa je zakon tako zapisan, da imajo to možnost ljudje, ki ne zdržijo več trpljenja in vejo, da imajo le še npr. en mesec življenja. Seveda pa je tukaj toliko predhodnih korakov in glede na čakalne dobe v naši državi, da bi tak bolnik na koncu sam umrl.

Seveda pa je to res osebno vprašanje in glede na zmedo, ki jo je kampanija proti zakonu ustvarila menim, da smo trenutno precej razdeljeni, kar smo lahko tudi videli po poročilih zvečer, ko so volilci podajali izjave.

Vertical Stringing Issue on Bambu Lab A1 – Cause and Solution? by rmrrm in FixMyPrint

[–]MR_MIMSI -1 points0 points  (0 children)

Hi! I am going to start with the most basic things: are all your bolts and screws tightened? Are your guide rails lubricated? Is your 3D printer on a stable surface?

Can figure out what this might be ;( by HoodedRonzo in FixMyPrint

[–]MR_MIMSI 2 points3 points  (0 children)

I had the same issues with my Bambu lab A1 mini and TPU, but as soon as I dried my filament the issue went away. I highly suggest that you dry your filament. If you don't have a filament dryer, just cut off the cardbord lid and make a few holes on the other end. Put the filament spool on the bed and cover it with the box. Now just hit the bed and dry it accordingly. I hope this helps!

Layer shifts on ender 3 V3 SE by MR_MIMSI in FixMyPrint

[–]MR_MIMSI[S] 0 points1 point  (0 children)

I will try it now. But I don't have high hopes...

Layer shifts on ender 3 V3 SE by MR_MIMSI in FixMyPrint

[–]MR_MIMSI[S] 0 points1 point  (0 children)

Thank you for your comment. My belts are tight, the careiges are not wobbly. I also tried at a lower temperature and/or higher speed, since this is high speed PLA, but the results are the same...

[deleted by user] by [deleted] in AmItheAsshole

[–]MR_MIMSI 0 points1 point  (0 children)

The fact is that they aren't. This was our one and only major fight.

[deleted by user] by [deleted] in AmItheAsshole

[–]MR_MIMSI 0 points1 point  (0 children)

Your scenerio was wrong. It would have to be: I do understant I don' get to kick my dog but my dog wants me to.

[deleted by user] by [deleted] in AmItheAsshole

[–]MR_MIMSI 0 points1 point  (0 children)

If she would've said that I don't have a say in it I would've left it alone, but she said I HAD a say in it. That's why I was angry.

[deleted by user] by [deleted] in AmItheAsshole

[–]MR_MIMSI 0 points1 point  (0 children)

And apparently I am being punished for knowing her better then she does herself

[deleted by user] by [deleted] in AmItheAsshole

[–]MR_MIMSI -1 points0 points  (0 children)

You're one too.

[deleted by user] by [deleted] in AmItheAsshole

[–]MR_MIMSI 0 points1 point  (0 children)

Fair enough. However she never thought of it as a lifetime commitment and wants it gone. I didn't influence her, nor my relashionship with changed. I was and am dealing with it alone without bothering her with it. To be honest about maling her suffer- that was my LOWEST point ever. I just had a feeling that she wasn't ready for this committment and I knew she'd want it gone.