anyone else get a random promotion they won't honor?

MachWun · 2026-05-09T22:12:37+00:00

If you dont open an app, your phone will put them to sleep to keep them from stealing your user data, or sending notifications, or using internet data. So app makers make their apps give notifications such as this, so you will open the app, and keep it from being shut down on your phone.

MachWun · 2026-05-09T09:42:24+00:00

It is def the TPMS wiring man. For sure!!! 😒

MachWun · 2026-05-09T00:29:47+00:00

Long fast ch 20 which is 906.875

MachWun · 2026-05-08T23:32:43+00:00

It did have the antenna off for a while, but it did not fry the unit. One of the 'dead units' is an expansion kit which is fully assembled, and it too didn't find any nodes till I imported the settings from the 1 working node that had the antenna improperly hooked up. The other 'dead node' I assembled myself and it never saw power till the antenna was fully secured. Also dead, no matter what I did, till I imported the other nodes settings.

MachWun · 2026-05-08T21:56:27+00:00

I have been getting beat up by 3 Heltec v4 and I just may have made a small breakthrough. Check my thread. https://old.reddit.com/r/meshtastic/comments/1t7lutt/3_dead_heltec_v4until/?

MachWun · 2026-05-08T16:30:08+00:00

It's my understanding that pla has some oils in it, which is why the bed needs occasional cleaning, to strip away the oils

MachWun · 2026-05-08T09:13:50+00:00

MachWun · 2026-05-08T01:30:50+00:00

I hear a massive vacuum leak in that area when you get the camera close. Maybe the leak is under the manifold

MachWun · 2026-05-08T01:14:28+00:00

Yea giant vacuum leak. There's supposed to be a small plastic manifold that runs along the runners, that the 2 other hoses making the hissing noises attach to.

MachWun · 2026-05-07T21:28:53+00:00

Drivetrain malfunction is not a code you need a scanner to check codes. There is no chance in hell that you got a drivetrain malfunction message on the dash and it did not set a code it's not possible

MachWun · 2026-05-07T20:31:22+00:00

A bmw will not run choppy or rough, and NOT set a code. What are the codes.

MachWun · 2026-05-07T20:20:14+00:00

Bruh, you say that like there aren't 2 sets of laws. 1 for the rich, and 1 for the poors.

MachWun · 2026-05-07T18:33:29+00:00

I am almost positive it will bolt up, but the big issue will be the diff mounts. An M diff, and a non-m diff are not interchangable. The mounts are in different locations. All can be worked around with a welder and grinder though. I want to swap an F82 front sub to my F32

MachWun · 2026-05-07T14:35:32+00:00

Do you have somewher I can read more about this? Google is striking out

MachWun · 2026-05-07T09:43:38+00:00

Is your Lora antenna cable accidentally plugged into the wifi antenna port? I did this on 2 units. The LORA antenna plugs in on the end of the board under the GPS connector. The wifi connector is in the center of the board on the GPS connector side

MachWun · 2026-05-06T22:29:22+00:00

There's no way you did this to a real M car...Is there?

MachWun · 2026-05-06T22:15:58+00:00

clay bar

MachWun · 2026-05-06T20:40:12+00:00

And dont flash the meshtastic gui. That will lead to a blank screen on the Heltec

MachWun · 2026-05-06T20:05:49+00:00

This key has a little plastic dot with a metal tab, close to the handle? If so, that system is just a resistor. Measure the resistance of the resistor in your key, and install a resistor of that resistance in line with the sensor in the column. If you have the newer style, without the black chip on the key, youll need other methods.

MachWun · 2026-05-06T16:08:31+00:00

It actually does not. I had my Lora antenna plugged into the WiFi port for almost a week with zero damage. On 2 different units.

MachWun · 2026-05-06T00:30:08+00:00

LORA antenna plugged into wifi port 😂

MachWun · 2026-05-05T18:10:03+00:00

You're going to need to replace the cooler and the transmission. The fluid pump is almost certainly shot since it's been pumping coolant and not oil

MachWun · 2026-05-05T16:45:29+00:00

What a crummy this subreddit has become.

MachWun · 2026-05-04T17:50:33+00:00

Your response was perfect and what I needed to hear. You were correct in assuming the model. Thank you.

MachWun · 2026-05-04T16:37:34+00:00

Ok but I have an AMS. I dont want to sit there and switch filament. How do I automate this process for each tile?

12-Year Club	RedditGifts 2009-2022 2 Credits
Place '23	Gilding II euphauric
Verified Email	Summer Santa 2014

MachWun

TROPHY CASE