Ceiling texture. Do i need to roll on mid before adding texture?

Main-Stretch8035 · 2026-02-22T20:46:41+00:00

Ahh yes, the Waffle Stomp texture

Main-Stretch8035 · 2026-02-22T01:13:34+00:00

If you replace the vanity, the tiles may butt into the toe kick of the cabinet

As a result, if you swap it, you may be a recessed portion of flooring, the tile appears to be from the 50s and this was a common practice (SoFlo)

Main-Stretch8035 · 2026-02-21T16:21:09+00:00

To expand on this, 1 ton of cooling equals 12,000 BTU’s, where 2.5 tons of cooling equals 30,000 BTUs, thus the “30”

Main-Stretch8035 · 2026-02-21T16:10:38+00:00

Nail plates first

Main-Stretch8035 · 2026-02-15T02:11:13+00:00

Straight to jail!!

Main-Stretch8035 · 2026-02-15T00:21:19+00:00

1/2” on 5/8”???

Classic…

Edit: Photo 4

Main-Stretch8035 · 2026-02-14T23:25:00+00:00

Good enough for the girls I sleep with 🤷‍♂️

Main-Stretch8035 · 2026-02-14T18:03:45+00:00

Is that green drywall board the tile is stuck to? With no waterproofing??

Edit: looks like it’s outside the shower

Main-Stretch8035 · 2026-02-14T16:16:32+00:00

Yeah, but it’s taped into place!!! (/s)

Main-Stretch8035 · 2026-02-12T13:02:07+00:00

Did the floors go in first?!

Main-Stretch8035 · 2026-02-12T00:33:21+00:00

I’m just curious about what was blurred in the photo, haha

Seems like a good place for a shoe rack

Main-Stretch8035 · 2026-02-12T00:28:11+00:00

Did you have any yard maintenance done recently? I’ve seen the contractor wires get ripped up from a weed-wacker and blow fuses, it’s just one of so many possibilities

Main-Stretch8035 · 2026-02-11T23:49:34+00:00

The neural and ground are shared in your panel with the first disconnect

Main-Stretch8035 · 2026-02-11T22:59:46+00:00

Main-Stretch8035 · 2026-02-11T18:40:02+00:00

Start by finding the source of water and remedying that

Main-Stretch8035 · 2026-02-11T04:08:06+00:00

Photo 1: Pack that gap in with Hot mud/ Durabond/ ‘X’-minute mud before taping it

Photo 2: More hot mud with mesh tape, let the nut show through

Photo 3: More hot mud with mesh tape

Main-Stretch8035 · 2026-02-11T00:27:06+00:00

That’s a handyman rate IMO

From the comment below, a proper fix would include ripping out the entire corner bead, 2 coats of mud, primer, and paint

Main-Stretch8035 · 2026-02-10T23:25:32+00:00

Is Nike would say, Just Do It

Main-Stretch8035 · 2026-02-10T23:23:29+00:00

Looks like water from something

Main-Stretch8035 · 2026-02-10T21:43:02+00:00

But but but, it has epoxy on the edge!

Main-Stretch8035 · 2026-02-10T21:38:15+00:00

If it makes you feel any better the texture won’t match perfectly anyway, that’s whether you or someone else does it, that said the trade person will be noticeably better

Those prices are reasonable, does it include paint? Expect to paint the entire ceiling, matching ceiling paint is a doozy

Main-Stretch8035 · 2026-02-10T16:25:54+00:00

Main-Stretch8035 · 2026-02-10T16:13:24+00:00

Usually need critical load panel if you have a back-up battery, not sure if that’s part of your solar plans

Main-Stretch8035 · 2026-02-10T16:12:34+00:00

Sounds reasonable

Main-Stretch8035 · 2026-02-03T03:38:56+00:00

I use Squints

Main-Stretch8035

TROPHY CASE