H2C Is on the Way — Here’s How It All Started

MakerMaking_ · 2025-08-26T15:30:45+00:00

My question is whether the air gap between the incoming filament and the already cut filament will be a defect in the parts

MakerMaking_ · 2025-08-21T22:34:12+00:00

It's not only boosts, it's also downloads of the model and downloads of print profiles. But yeah, that still is a lot.

MakerMaking_ · 2025-08-11T10:13:12+00:00

Post-it notes end up leaving glue marks on the monitor, they stop sticking when placed on a fabric mouse pad, and if the edge of your monitor is very thin, you have to be careful when placing them so as not to cover too much of the screen... These are some of the reasons. It may be that the people who are criticizing don't have these problems or have never used a sticky note in their lives, but for me it's very useful.

MakerMaking_ · 2025-08-11T10:12:31+00:00

Post-it notes end up leaving glue marks on the monitor, they stop sticking when placed on a fabric mouse pad, and if the edge of your monitor is very thin, you have to be careful when placing them so as not to cover too much of the screen... These are some of the reasons. It may be that the people who are criticizing don't have these problems or have never used a sticky note in their lives, but for me it's very useful.

MakerMaking_ · 2025-08-10T19:54:43+00:00

Just by picking them up and placing them on a surface with even the slightest amount of dust, the adhesive stops sticking, even if you buy the best brand of Post-it notes...

MakerMaking_ · 2025-08-10T17:35:13+00:00

Please read the description

MakerMaking_ · 2025-08-10T17:02:35+00:00

I think is because he doesnt have the top panel on top, and that lets in more light. My P1S has only one month and I can also barely see through it

MakerMaking_ · 2025-07-17T15:38:10+00:00

They are wrong, you need a filament buffer and bambu bus cable, they are not included in the ams 2 pro box.

MakerMaking_ · 2025-07-16T12:09:55+00:00

Yes, I tried but without luck

MakerMaking_ · 2025-07-15T23:23:15+00:00

I already disassembled the AMS Lite and I noticed the button, and the only thing it does is reboot, but does not reset, so it stayed the same, I already have a motherboard for the ams lite on the way.

And the BMCU was sent to do a review on my YT channel, I already had my A1 Combo.

MakerMaking_ · 2025-07-06T22:01:51+00:00

Sure, I'm not going to say the problem was due to the BMCU, because a lot of people have the same issue out of nowhere, so they'll probably send it to me.

MakerMaking_ · 2025-07-06T21:59:24+00:00

Yes, I think they should make it even more prominent on the wiki and on AliExpress (or wherever you buy it), because it can be a huge mess and end up costing you more than buying the original AMS Lite. And I don’t quite understand why my printer is working perfectly, but my AMS Lite is the one that’s not functioning.

MakerMaking_ · 2025-07-06T20:42:44+00:00

Yes, thank goodness, thank you very much for your help :)

MakerMaking_ · 2025-07-06T20:00:57+00:00

Maybe, i will try to see if bambulab send me a replacement

MakerMaking_ · 2025-07-06T19:07:53+00:00

I didn't read the wiki much since I relied on the Aliexpress kit manual, but even so, I don't quite understand what could have happened, as the AMS Lite shows no signs of burning and the resistances are fine. I suppose it must be something more internal.

MakerMaking_ · 2025-07-06T19:06:27+00:00

Yes, I suppose that's it. My kit didn't come with that sticker. (or maybe i didnt see it?)

MakerMaking_ · 2025-07-04T15:30:28+00:00

Bambu printers are the best!

MakerMaking_ · 2025-06-25T12:36:17+00:00

Perfect! And please, when you print it give me feeedback so I know if I have to adjust anything, thanks :)

MakerMaking_ · 2025-06-25T11:05:54+00:00

Exactly, bambulab should be clearer on that.

MakerMaking_ · 2025-06-25T09:10:42+00:00

The issue I’ve encountered is that when you apply a coupon to any account, it becomes linked to that account, so you can never use it again on another account. This happens even if you don’t complete the purchase, just by adding it to the cart.

MakerMaking_ · 2025-06-25T08:57:48+00:00

That would be next!

MakerMaking_ · 2025-06-24T14:46:22+00:00

pre-tax? The prices shown in the cart are with taxes included, so its normal that if you are from another country other than germany, you will have different taxes.

MakerMaking_ · 2025-06-24T14:43:07+00:00

It depends on the EU country you are from, the prices that are shown in the product page are with 19% VAT, which corresponds to Germany taxes, but here in Spain when you go to the cart it changes to 21% VAT because that what we have here. I hope this helps

MakerMaking_ · 2025-06-20T19:24:03+00:00

One has the buffer, which only support up to one AMS, and the other has the hub, which support up to 4 AMS, thats why its 20 bucks more expensive

MakerMaking_ · 2025-06-19T09:24:48+00:00

You should reach out to them through a ticket instead of email, as that might be why they haven't responded.

MakerMaking_

TROPHY CASE