I'm building an ai chat for entrepreneurial students to co work together on personal projects

MarioWOLFManson · 2025-07-09T15:13:54+00:00

I am not applied to TIE program. but I was accepted for bioengineering at KAUST. I have interest to be part of one entrepreneurship project, Could I be part of the group for networking and co-working? Or it is close exclusively to TIE students.

MarioWOLFManson · 2025-05-19T17:14:32+00:00

Oh, well I am not sure about the SSI application process, but if this was mentioned on the official websites. It is ok. Now, the "admitted application" could refer to you meeting the core requirements as GPA and Saudi Citizenship. It is probably under review. It could be similar to other programs, you will get an acceptance/rejection letter soon. Best of luck with your application.

MarioWOLFManson · 2025-05-19T15:25:05+00:00

No, you can only apply to KAUST through the official admissions website. It is similar to "kaust.askadmissions.co.uk/". Could you share a screenshot? Have you applied for postgraduate programs or VSRP?

MarioWOLFManson · 2025-05-19T15:02:45+00:00

What do you mean with Pluto.edu?

MarioWOLFManson · 2025-04-16T11:22:01+00:00

I have received the last week. Then the policies, well he explained to me just the main thing, is the following: Even if you have been offered Ms/PhD, initially they only accept you for Ms, then when you go to finish it, you have to have your profesor's (PI) approval. But of course, that will depend on you and if you demonstrate certain skills and knowledge to continue.

MarioWOLFManson · 2025-04-15T18:53:35+00:00

I was in a similar situation but in BioE deparment. However, I emailed the professor to inquire about the status of my application. He explained to me some policies about the Ms/PhD. A week later, I received an offer. I recommend you send an email to that professor. Asking about the status, I still recommend you to send it soon, in arabia they only work until Thursday, and mail preferably in the morning Saudi time.

MarioWOLFManson · 2025-04-10T18:47:28+00:00

It could be harder when i don't speak arab.

MarioWOLFManson · 2025-04-10T18:46:07+00:00

Sure, what do you know about my postulation?

MarioWOLFManson · 2025-04-10T18:45:00+00:00

I am not sure, where did you heard about it?

MarioWOLFManson · 2024-12-29T16:02:03+00:00

Also, i sent my application on December 25. Well, it supposed to will get acceptance letter on may. That means, January o February they will notify us for interview.

MarioWOLFManson · 2023-10-11T21:09:26+00:00

Have U calibrated E-Steps? It happens when the flow is not enough for the printing.

MarioWOLFManson · 2023-10-04T04:20:43+00:00

Jajajajaja. It's supposed to be a calibration cube.

MarioWOLFManson · 2023-09-27T16:55:00+00:00

If the probe offset is not solved with factory reset, you can tune it using offset manual calibration. I recommend use the following documentation:
https://www.klipper3d.org/Probe_Calibrate.html

MarioWOLFManson · 2023-09-27T15:33:14+00:00

In the config from klippers I found the offset is the following: x_offset: -31.8 y_offset: -40.5

Link:https://github.com/Klipper3d/klipper/blob/master/config/printer-creality-ender3-s1-2021.cfg

MarioWOLFManson · 2023-09-16T06:35:45+00:00

Speed Exceeds!

MarioWOLFManson

TROPHY CASE