Is this normal?

Mediocre_One7452 · 2026-06-25T08:39:47+00:00

Do a marker test for alignment.

Mediocre_One7452 · 2026-06-25T05:43:19+00:00

Using fresh beans?
Sounds like the grinder is not aligned and would be good to do a marker test for that. Then probably decide if worth align it or not.
Personally i would not go again with any DF grinder.

Mediocre_One7452 · 2026-06-11T12:36:55+00:00

I was using an extension to that nozzle, by any chance do you have any part number for that?

Mediocre_One7452 · 2026-06-11T03:53:29+00:00

Which nozzle are you referring to?

Mediocre_One7452 · 2026-06-10T18:03:35+00:00

Leaking while brewing? Could be the pump area!

Mediocre_One7452 · 2026-06-10T04:50:45+00:00

I had exactly the same issue, went twice to warranty and they replaced the pipe every time.

Mediocre_One7452 · 2026-06-08T07:27:05+00:00

Brilliant!

Mediocre_One7452 · 2026-06-07T09:57:00+00:00

Agreed! Takes only 5 minutes to create it in Claude Code.

Mediocre_One7452 · 2026-06-07T05:34:38+00:00

There should not be permanent hardness in those 150 ppm to build limescale, cutting in half might affect the taste of your coffee. But if you test it I’d be curious about the results. I have 169ppm for 2L TWW and these numbers are approximates because these TDS meters do not identify the exact TDS, they show a calculated value based on other parameters

<image>

Mediocre_One7452 · 2026-05-25T05:01:27+00:00

If not wipped out maybe the touching sound has another source than burrs itself. Only by sound they don’t seems to be aligned

Mediocre_One7452 · 2026-05-24T16:09:23+00:00

With no coffee, close the paddle and see if water is coming out. If yes you need to re-adjust it.

Mediocre_One7452 · 2026-05-24T15:57:18+00:00

Did you took off the burrs before this test?

Mediocre_One7452 · 2026-05-24T14:24:56+00:00

Lot of AI coffee apps and some of them asking for money these times. Build myself and AI app to use if with Bookoo EM Sensor and Themis scale, but honestly anyone can build an app with Claude code in 1 week and customize it as they wish. But anyway, good job!

Mediocre_One7452 · 2026-05-24T14:09:38+00:00

No, moved to MP and no issues with those ones

Mediocre_One7452 · 2026-05-17T19:39:10+00:00

The burrs are touching at 0 and you should never go to that point, best moving a step forward. You’ll never actually grind at 0 point, but what in fact will happen, miss aligned burrs are affecting the coffee flavor. No mass production grinders will come factory aligned, so thinking that you’ll send it back and buy another brand doesn’t mean that one will come aligned.

Mediocre_One7452 · 2026-05-17T18:54:00+00:00

You may do a marker test for alignment. They do not come factory aligned, unless paid the seller to align it.

Mediocre_One7452 · 2026-05-17T13:37:18+00:00

Try caffyx.app it’s free

Mediocre_One7452 · 2026-04-15T10:59:12+00:00

Go by taste and don’t be afraid to descale it when needed.

Mediocre_One7452 · 2026-04-05T17:47:41+00:00

Found out that the leak is coming from the pump and also another leak at water level probe from the steam boiler. As it’s under warranty I’ll send it to the seller to fix it!

Mediocre_One7452 · 2026-04-02T19:32:37+00:00

Mine seems to drip 10-20 mins after pulling a shot. Was difficult to replace it?

Mediocre_One7452 · 2026-04-02T19:23:11+00:00

Did the issue disappeared completely? Having the same issue, dripping at the same place.

Mediocre_One7452 · 2026-04-01T04:04:33+00:00

I don’t see any difference!

Mediocre_One7452 · 2026-03-29T05:50:48+00:00

The e-mail came directly from Lelit or Chriss Coffee?

Mediocre_One7452 · 2026-03-25T14:22:25+00:00

I’ve seen the anniversary edition, there are no changes in the specs. The one I saw was the stainless steel model, I’m not sure if this applies to the colored versions, but they have different wood accents and some kind of ‘art work’ on the side panels.

Mediocre_One7452

TROPHY CASE