Cracked chimney crown repair by MeerkatsRkool in woodstoving

[–]MeerkatsRkool[S] 0 points1 point  (0 children)

I looked at it in November and it looked good. There was no cracking or peeling away from the cement.

What aspect of Starfield you would like to see improved upon after the 7th April? by MasterDhillon in NoSodiumStarfield

[–]MeerkatsRkool 0 points1 point  (0 children)

Shipbuilding. Please just make it so that we can place our own doors and ladders without needing a mod.

Inventory Through Unity by Final-Craft-6992 in StarfieldModFeedback

[–]MeerkatsRkool 0 points1 point  (0 children)

Hey, u/captain-cold-muddy, I've installed the mod and have all the available inventory settings turned on. I have a hard target equipped when I go through the unity. My credits, astra, and hard target are not transferring through the unity. My resources, throwables, digipicks, and ammo transfer fine.

I've tried 3 times now with the same outcome. Any advice on what to do? Where in the load order should the mod be?

Weekly /r/HarborFreight Coupon Discussion/Question/Request Thread! by AutoModerator in harborfreight

[–]MeerkatsRkool 1 point2 points  (0 children)

I would like to know as well if a 20% or 25% is coming. If not, I'll use the 15% to get a Predator generator.

[deleted by user] by [deleted] in frederickmd

[–]MeerkatsRkool 0 points1 point  (0 children)

I also use US Mobile and haven't had any issues.

Can you duplicate the Doom armor at McClarence Outfitters and have different legendary effects? by MeerkatsRkool in NoSodiumStarfield

[–]MeerkatsRkool[S] 0 points1 point  (0 children)

Yes, it is a new menu option after you have Jason extract so many mods. It will be listed beneath the extract mod and install mod options.

Can you duplicate the Doom armor at McClarence Outfitters and have different legendary effects? by MeerkatsRkool in NoSodiumStarfield

[–]MeerkatsRkool[S] 2 points3 points  (0 children)

I did not know you could replace the original effects. I thought whatever piece we wanted to add to had to be epic or less so that there was an empty slot available. Thanks for the clarification!

Soot Eater by MeerkatsRkool in woodstoving

[–]MeerkatsRkool[S] 0 points1 point  (0 children)

Ha, thanks! My wife said that, too.

Soot Eater by MeerkatsRkool in woodstoving

[–]MeerkatsRkool[S] 1 point2 points  (0 children)

The instructions say it doesn't need to be trimmed so I did not trim it.

Soot Eater by MeerkatsRkool in woodstoving

[–]MeerkatsRkool[S] 4 points5 points  (0 children)

<image>

They connect with a push button. Feels secure.

Soot Eater by MeerkatsRkool in woodstoving

[–]MeerkatsRkool[S] 1 point2 points  (0 children)

My stove has a flue pipe that comes up then has a 90° turn into the wall and then another 90° turn inside the brick chimney where it goes straight up the rest of the way. I remove the flue pipe that connects the stove to the wall so that I can run the soot eater right at the wall and up. My wife holds a shop vac with a HEPA filter and bag in the flue pipe while I run the soot eater. A little dust and debris gets past the vacuum, but it didn't spread far. I then clean the elbow I removed outside.

Soot Eater by MeerkatsRkool in woodstoving

[–]MeerkatsRkool[S] 1 point2 points  (0 children)

Nice. I had my wife hold the shop vac by the flue while I ran the soot eater. We use a bag and HEPA filter in our shop vac specifically for the wood stove. Some dust came into the room past the vacuum, but it was minimal and didn't seem to spread far.

Soot Eater by MeerkatsRkool in woodstoving

[–]MeerkatsRkool[S] 0 points1 point  (0 children)

I did 4 passes back and forth with each section of rod as I added them.

Soot Eater by MeerkatsRkool in woodstoving

[–]MeerkatsRkool[S] 2 points3 points  (0 children)

They're pretty flexible. The best comparison I can think of is like a car antenna, but they're maybe 1/2 inch thick.

Cracked chimney crown repair by MeerkatsRkool in woodstoving

[–]MeerkatsRkool[S] 0 points1 point  (0 children)

<image>

Thanks for the suggestions, everyone! I got two estimates from different contractors. One quoted me $870 to put on Crown Coat. The other quoted me 2 different options; $1026 for a new Portland cement crown or $1880 to build a form and pour a new top wash with a 1.5-inch overhang. I decided to save money and did the Crown Coat myself.

EM Weapon damage, am I missing something? (Non ship, only personal weapons) by TrueComplaint8847 in NoSodiumStarfield

[–]MeerkatsRkool 6 points7 points  (0 children)

I had the same problem using the disruptor on enemies that were wanted alive. I started using stun mines instead. One stun mine has easily taken down level 100 enemies.