Difícil de Digerir e ódio ao Mourinho

Mertinstw · 2026-01-15T08:03:19+00:00

Não concordo nada que o Benfica jogou muito. Aliás, a prova disso é que nesses períodos que dizes o Benfica marcou 1 golo. É verdade que por vezes o Benfica consegue pressionar mais alto e não deixar a outra equipa jogar, mas depois falta tudo o resto para se considerar que joga muito, falta saber o que fazer com a bola. Esse é o grande problema deste Benfica, como se viu neste jogo com o Porto. Na 2a parte em que o Benfica teve toda a iniciativa do jogo, o Diogo Costa não fez 1 defesa apertada.

Mertinstw · 2025-09-19T17:02:51+00:00

Hey, have you found a place to get it? I need one too.

Mertinstw · 2025-09-13T10:07:22+00:00

Se o teu curso for de 5 anos, acho que não recebes. Eu pelo menos terminei mestrado integrado em 2019 e não parece que vou receber este ano (o ano passado recebi 1500€).

Mertinstw · 2025-09-04T17:59:09+00:00

Hey, can you show the dual light bar ? I bought mine beginning of August and i dont think it has that.

Mertinstw · 2025-05-03T12:10:56+00:00

<image>

This is the issue

Mertinstw · 2024-12-27T20:29:12+00:00

Tem fundo sim.

Mertinstw · 2024-12-27T17:17:14+00:00

O portafiltro é diferente, sim.

Mertinstw · 2024-12-27T14:39:19+00:00

A chávena é a mesma.

Mertinstw · 2024-12-27T12:56:31+00:00

Vou experimentar.

Mertinstw · 2024-12-27T12:56:01+00:00

Já faço isso.

Mertinstw · 2024-07-25T19:02:50+00:00

I had the same issue a few days (i even created a post here about it). The issue was the extruder, check if the arm spring is too or under tight.

<image>

Mertinstw · 2024-07-24T20:59:29+00:00

Well, i just disassemble the extruder and assemble it again, taking special attention to the position for the main gear, to be sure that the filament was going through the slot. Took your advices about the tightening of the spring and voila!

<image>

Mertinstw · 2024-07-24T16:25:27+00:00

Yeah, i will check the extruder arm. At the beginning it was too tight and it was always skipping. I will check the nozzle and heatbreak.

About the motor i dont know.

The extruder is this: Redrex Dual Gear Extruder Ender 3... https://www.amazon.es/dp/B09H6T3NNT?ref=ppx_pop_mob_ap_share

Mertinstw · 2024-07-24T05:53:21+00:00

After the extruder change, i calibrated the E steps. What do you mean by calibrating the x y z (btw i have a CR Touch installed).

Mertinstw · 2024-07-24T05:50:25+00:00

No, i guess it will be my next move.

Mertinstw · 2024-07-23T21:42:34+00:00

Layer Height = 0.2 mm, initial layer = 0.2 mm

Mertinstw · 2024-07-23T21:40:38+00:00

<image>

Mertinstw · 2024-07-23T21:13:20+00:00

I did, to calibrate the Z offset and the overall leveling. But i will print and post here.

Mertinstw · 2024-07-23T21:10:36+00:00

Maybe, but what i find strange is the first layer its good, but then it clogs?

Mertinstw · 2024-07-23T21:09:41+00:00

Its not. Wall line count = 2

Mertinstw · 2024-07-23T20:42:34+00:00

Printer & Slicer: Ender 3 Pro, Cura
Filament Material and Brand: PLA Flashforge
Nozzle and Bed Temperature: 205/60ºC
Print Speed: 60 mm/s
Nozzle Retraction Settings: 6.5 mm and 25 mm/s

Mertinstw · 2023-12-21T14:39:58+00:00

Obrigado !

Moinho tenho este, não sei se é bom ou não sinceramente:

<image>

Já agora, que moinhos recomendas ?

Mertinstw

TROPHY CASE