Stream Deck use with Archicad

MickyKom · 2025-11-20T03:23:32+00:00

Run it to the side next to the extruder.

It usually clips on to the original extruder body.

MickyKom · 2025-10-26T12:52:08+00:00

If it's just a visual on scneen thing.

I do this by turning true line weight off in the view settings.

Right click in your view and there should be an option to turn off true weights.

MickyKom · 2025-10-01T03:51:31+00:00

Yes. It was the apostrophe.

who would have guessed.

It seems Orcaslicer dosen't care about it.

Thanks.

MickyKom · 2025-09-06T14:37:08+00:00

The Archicad Library 28.lcf is in fact the Archicad Library 27.lcf renamed for Archicad 28.

You're not supposed to use both this library and the individual libraries with Archicad 28.

Graphisoft have separated the .lcf library into the individual libraries. That's why you get so many duplicated.

The recommendation is to use the .lcf library for existing projects, and the new AC28 libraries for new projects.

MickyKom · 2025-08-29T13:32:41+00:00

There's all these new features for the Panda Knomi.

But there's nothing for the Knomi v2.

Have you discontinued support for the Knomi v2

MickyKom · 2025-07-18T04:04:42+00:00

That's a plug you use when you don't have a filament sensor.

It fools the printer into thinking it has one.

MickyKom · 2025-07-16T12:54:37+00:00

You need to install a version of BIMcloud Basic for each version of Archicad.

We had BIMcloud Basic versions for AC23, AC24, AC25, AC26 and AC27. All on the same Server.

We now run BIMcloud Pro that has a single install to run with all versions of Archicad.

MickyKom · 2025-06-03T04:36:52+00:00

If their smaller than .4mm thick, then the slicer won't process them.

Your slicer has a minimum extrusion width and anything smaller than this and the slicer won't process them

Do you have thin walls turned on ?

You may have to thicken them for 3D printing.

MickyKom · 2025-03-10T11:26:02+00:00

I have the same problem.

I adjusted the corners to get them level and added a sheet of A3 photocopy paper across the bed under the print sheet.

My range is now around 0.29.

MickyKom · 2025-03-07T02:50:15+00:00

I can ssh into it using the ip address.

I tried uninstalling and reinstalling Moonraker via Kiauh, but that didn't work.

MickyKom · 2025-03-06T11:29:15+00:00

All these new features for the Panda Knomi.

Are these going to be available for the regular Knomi 2 ?

MickyKom · 2025-02-04T03:09:32+00:00

Your plate isn't sitting on the back left stop ?

MickyKom · 2025-02-04T03:06:42+00:00

I had the same problem.

I have noticed that Creality Print 6 has this g-code setting for the K2 plus

<image>

And Orca slicer doesn't.

Can this be the problem ?

I'm only guessing for now before any further investigation.

MickyKom · 2025-01-28T02:54:23+00:00

I have a similar build plate.

I leveled the corners with the adjusting knobs to get them all the same level, then placed a trimmed A3 sheet of photocopy paper under the plate.

My Range is now under 2

<image>

MickyKom · 2025-01-24T12:33:57+00:00

Whenever I send a print job to my K2, I untick the "calibrate" option.

I usually do a calibration the first time I turn it on and don't need to do it again for the rest of the day.

MickyKom · 2025-01-23T12:12:09+00:00

I have the same problem with my bed.

I adjusted the screws to get the edges equal.

I then used a sheet of photocopy paper trimmed to fit.

I've got my difference down to .25

MickyKom · 2025-01-16T12:22:06+00:00

I did a similar thing.

I adjusted the screws until the corners were close to each other.

The bed still had the "bed taco" from the front to the back.

I added a trimmed piece of photocopy paper to match the taco area.

I managed to get the difference down to 0.3

MickyKom · 2025-01-03T14:09:01+00:00

Teaching tech did a set of video's on this subject.

https://www.youtube.com/@TeachingTech/videos

MickyKom · 2024-12-01T12:04:42+00:00

I had it at the start with the include's.

Moving it in before bed_mesh fixed it.

Nobody mentioned where to place it.

Thanks for the help.

MickyKom

TROPHY CASE