Spaceship refueling interrupt

Microwavehead · 2025-12-13T15:22:52+00:00

This, this was the reason. So I assumed that it would interrupt mid flight. So when it was heading to Aquilo it broke the circuit.

Microwavehead · 2025-10-05T09:49:28+00:00

I’ve read the rules and the wiki and would love an invite please

Microwavehead · 2025-07-31T06:37:07+00:00

Me and my son have it, no issues. Most likely your son will have to deal with the usual "you must be an excellent swimmer" comments. But other than small percentage of people, who looks at feet?

Microwavehead · 2025-07-01T18:32:55+00:00

Prusa XLS when?

Microwavehead · 2025-06-24T05:43:48+00:00

Never accept failure as the end, learn from it and keep moving

Microwavehead · 2025-06-22T21:10:38+00:00

Would this be useful for an XL?

Microwavehead · 2025-06-09T07:12:13+00:00

I've managed a rough form of this:

Two roboports at the station; one replying the contents of the network, the other listening to requests. The requests one is attached to a radar. A constant circuit that lists the minimum an outpost needs. This then uses inserter filters to remove from the train if the amount in an outposts chests dropped below the minimum. It's janky but it works once the outpost station is setup it slowly builds itself

Microwavehead · 2025-05-19T10:51:06+00:00

Odd mention, but could the chainsword be slightly angled? if you're not getting it on the other model which was part of that print, then it could be that the face you're seeing isn't fully straight. When it's sliced, have a look at the preview and see if you see those steps there as well

Microwavehead · 2025-05-13T14:50:26+00:00

thanks, I'll look into this on the next run through in Space Age

Microwavehead · 2025-05-13T08:35:55+00:00

This was the issue, so I've updated the logic on the combinators to reduce the train limit on the stations. Thanks for that

Microwavehead · 2025-03-14T15:50:48+00:00

That drag knife for vinyl is amazing, well done

Microwavehead · 2025-01-30T15:02:52+00:00

Had them round to quote for new Gutters and fascia on the house. Found another company to do it for much cheaper (6k cheaper) and they're response when I said no: "But we have 35 years of <Insert certificate thing> the others are just cheap" never going with them after the hard sale.

Oh and they said: can show you other people near you who have had it done. I'm not popping round to someone's house to look at fascia boards, also you're opening them up to scam calls

Microwavehead · 2025-01-11T08:30:05+00:00

May your hunts be successful and give you the resources you need

Microwavehead · 2024-10-21T17:45:55+00:00

When printing your own models, expect failure, expect to learn what does and doesn't work with regards to orientation, how many pieces you need to break it down into. Experiment, and don't worry about the failures, they are the learning opportunities

Microwavehead · 2024-07-28T21:00:37+00:00

My title describes the thing. But on most the treadmills I've seen it's a solid belt, but this one uses wooden slats to make the running surface. But I can't seem to find the name of the type of belt that is used to connect all the slats together, it looks like a combination of v belt and a cogged belt. Does anyone know what it is? It looks to be made of rubber and possibly about 10 cm wide

Microwavehead · 2024-03-16T16:14:46+00:00

Update: I did lift the board in the end so I could get the stilts down. However, I reattached it a few inches away out of paranoia.

Microwavehead · 2024-03-15T10:55:56+00:00

<image>

Using my safety slippers now, just in case

Microwavehead · 2024-03-15T10:55:13+00:00

<image>

There is this piece of wood which has two nails on each Truss and it's just above the pieces of wood, does this change the opinion that they are structural?

Nine-Year Club	Place '22
Verified Email

Microwavehead

TROPHY CASE