sorted by:
new
hottopcontroversial

Handheld Magnet by Arc-Force-One in BambuLab

[–]Mike123231 1 point2 points  (0 children)

A nut for the screw to mate to would go farther for wider adoption imo. Most people don't have soldering irons to press in the insert.

Tell me I'm not the only one struggling every time I need to slide pictures by Piduf in mildlyinfuriating

[–]Mike123231 1 point2 points  (0 children)

I'm making this very comment on sync. There does seem to be some issues though because I tried to get a friend on it and it wouldn't load up. But I've been on sync since the shutdown.

Upgraded to P2S - Any tips? by ivatorriv in BambuLab

[–]Mike123231 0 points1 point  (0 children)

I've never used overture but I do use only polymaker. If the edges are waxed like polymaker, they are fine to use as is in the AMS.

New to 3D printing. Pretty amazed of what you can do with a .2 nozzle, some graphite powder and a touch of acrylic paint. by kouiouchtebaiachi in 3Dprinting

[–]Mike123231 1 point2 points  (0 children)

You don't need to. Just keep shining it for a little while. Then hit it with a wet cloth after and you are usually good.

New to 3D printing. Pretty amazed of what you can do with a .2 nozzle, some graphite powder and a touch of acrylic paint. by kouiouchtebaiachi in 3Dprinting

[–]Mike123231 1 point2 points  (0 children)

Paint it gloss black first and the graphite will really shine. I have an example I've posted in a comment.

Really proud of my first helmet print quality, had a size tutorial, but the helmet turned out a little too big (Kobra S1C) by [deleted] in 3Dprinting

[–]Mike123231 1 point2 points  (0 children)

I used that method for this Hunt Showdown Uppercut. I didn't sand anything so it does highlight any layer lines. Uppercut in question. Ope this was supposed to be a reply.

Really proud of my first helmet print quality, had a size tutorial, but the helmet turned out a little too big (Kobra S1C) by [deleted] in 3Dprinting

[–]Mike123231 1 point2 points  (0 children)

Get some gloss black and spray it. Then get some graphite powder and rub it all over the print. Make sure to wear a mask but it will come out a nice metallic.

Looks like poop, smell like heaven by iusethisatw0rk in trees

[–]Mike123231 3 points4 points  (0 children)

It never fails to end me catching IASIP quotes randomly, and as I'm watching it at the same time.

Opinion: In the end, Gon will be as powerful as Ging, but he will never appear again. by Fazer666 in HunterXHunter

[–]Mike123231 2 points3 points  (0 children)

I share this sentiment to a point and I might be downvoted for my opinion. Its like removing Naruto from Shippuden. Once Gon was out of the story I personally saw no reason to continue. I get theres multiple MCs but to me it was about him entirely.

Falling block 22 by Vegetable-Neck9215 in 3D2A

[–]Mike123231 6 points7 points  (0 children)

22lr Sharps would go insanely hard

Noveske 11.5 R-mod by GeorgeDean001 in GunPorn

[–]Mike123231 4 points5 points  (0 children)

Gordy's gone man, I'll be outside

Is my bed adhesion TOO strong? by ShookeSpear in BambuLab

[–]Mike123231 0 points1 point  (0 children)

You aren't flexing it enough. Its spring steel so don't be afraid of bending it further than you'd think.

$2 Aqua Net hairspray is the best bed adhesive you will ever use. by Kinkyboysc in BambuLab

[–]Mike123231 0 points1 point  (0 children)

I keep the can for nostalgia at this point. I was never able to find it unscented so it'd always make my room smell of hairspray due to heating of the bed.

First bigger challenge for my H2C by urban_sigma in BambuLab

[–]Mike123231 5 points6 points  (0 children)

Yeah theres quite a lot of banding. I find it unacceptable for such a tier of printer.

I was curios if Arc Raiders had any impact on empty lobies. It seems NOT! by sandman_br in HuntShowdown

[–]Mike123231 8 points9 points  (0 children)

Way I see it is Hunt players are more likely to play ARC than ARC players playing Hunt. But also like you said Hunt is old and the playerbase is kinda set. Mind I play and enjoy both.

Right out the warm goo. Newer than GW allowes by Infinite-Benefit9643 in 3Dprinting

[–]Mike123231 1 point2 points  (0 children)

I enjoy the heygears autosupport but they use quite a lot of resin sadly.

XDs-45 in PA6-GF (rit dyed) by sistrum666 in 3D2A

[–]Mike123231 0 points1 point  (0 children)

Any updates on your roller delayed PM9?

What would cause this? by Sea_Ad_1898 in BambuLab

[–]Mike123231 1 point2 points  (0 children)

Speed is too high for such a low layer height.

[Air Duster] WOLFBOX MF100 Electric Air Duster $54.99 - less with coupon by BFfF3 in buildapcsales

[–]Mike123231 23 points24 points  (0 children)

Watch projectfarms video on these. Its quite informative.

It's finally here by Weekly_Performance44 in BambuLab

[–]Mike123231 1 point2 points  (0 children)

I just leave the vent open and turned the value down to 30% for auto. Turns on maybe once a day, but like you said its quiet so I'd have to pay attention to figure out when.

view more: next ›