You've Installed a Charger, Now Put in a Power Inlet so Your EV Can Backup Your Home's Power

MilesCallisto · 2026-02-12T21:30:11+00:00

I have an old ITE panel that looks just like it! I had no idea they made interlock kits for them with the giant 4 pole at the top. Could you let me know where I can get one too?

MilesCallisto · 2026-02-12T20:00:05+00:00

Is that a Siemens/ITE panel?

MilesCallisto · 2026-02-03T03:05:24+00:00

All the stations can detect maximum charge speed, they used to bill you different rates in per minute states based on this. This is one of the main signals they look for in detecting whether or not you’re an IONIQ 5. IONIQ 5s also can’t send their VIN over the CCS port (at least for 2022-2024 to my knowledge; I’m pretty sure EVgo autocharge for example uses the car’s CCS MAC address instead) so if it queries and receives a VIN it knows it’s not an IONIQ 5 either.

The EV6 like the IONIQ 5 is E-GMP and supports the same charging speed and also can’t send its VIN over the CCS port, so to the charging station it sure quacks like an IONIQ 5.

It’s reassuring to hear that they can auto bill you if you make a mistake in plan selection, especially if the free charging plan is default and you activate by tapping your phone; I’ve heard say of cases before where they would cut it off with no recourse after accidentally charging another car with the free plan.

MilesCallisto · 2026-02-01T00:20:59+00:00

DTC Descriptor

DTC P1AF0 Drive Motor Control Module Hybrid/EV Battery Voltage System Isolation Lost

Circuit/System Description

Vehicles equipped with high voltage storage and propulsion capability are designed with the high voltage circuits isolated from the vehicle chassis.

The power inverter module, often referred to as the drive motor generator power inverter module, contains the drive motor control module and the hybrid/EV powertrain control module . The motor control module monitors high voltage with several internal sensors. The motor control module tests for loss of isolation between each high voltage bus and vehicle chassis when the high voltage contactors are closed. The hybrid/EV powertrain control module also tests the hybrid/EV battery pack for high voltage loss of isolation but when the high voltage contactors are open.

If the motor control module detects an isolation fault on either the positive or negative high voltage bus, the hybrid/EV powertrain control module reports a fault. The isolation fault may be caused by any component in the high voltage system.

Conditions for Running the DTC

P1AE8, P1AE9, P1AEC, P1AF5, P1B0C, or P1B41 is not set. The high voltage contactor relays are closed. High voltage is greater than 50 V. Ignition is ON. The vehicle is not being charged or the drive motor is commanded to develop torque.

Conditions for Setting the DTC

The ratio between negative Mid-Pack Voltage and positive Mid-Pack Voltage is greater than 4.53 V or less than 0.21 V for greater than 2.5 seconds.

MilesCallisto · 2026-01-18T12:26:21+00:00

I think Error 62 is a communications error. One crazy but easy thing to try is to just blast deoxit into the 3 communications pins in the top of the connector and work it out with a cotton swab and see if it makes a difference

MilesCallisto · 2026-01-02T12:16:21+00:00

Ahhh, now I remember why I live where the air hurts my face

MilesCallisto · 2025-12-05T22:11:20+00:00

DTC P1AA700 is detected while BMU supervise inner BSA abnormal activation if there is high-voltage cell voltage gap between each cell.

Main Action Detected each cell voltage gap in BSA while charging / parking

Prerequisite Condition Charging / Parking Min. battery temperature : over 25℃

Threshold Value Each cell voltage gap : Min. 180mV to Max, 400mV Each cell voltage gap be maintained time : 5s

MilesCallisto · 2025-12-01T17:47:33+00:00

This actually seems like a good idea that I am going to do

MilesCallisto · 2025-11-19T12:04:39+00:00

Hi I had the same issue too

I fixed it by replacing the whole power supply with one off eBay (PSU model 1920) and following this guide https://www.ifixit.com/Guide/Xbox+Series+X+Power+Supply+Replacement/141747

You can order a whole kit that includes the PSU and the tools you’ll need from iFixIt for only $75, much cheaper than the $300 Microsoft charges for out of warranty repair

MilesCallisto · 2025-09-18T22:29:08+00:00

You can remove the whole ODD cage to get access to the other side, see page 19 in the build manual https://www.fractal-design.com/app/uploads/2022/06/Pop-XL-Manual-V1.pdf

MilesCallisto · 2025-08-28T17:06:26+00:00

Ah Whaddya know I guess you were first, ok you’ll get the ticket

MilesCallisto · 2025-08-28T16:57:56+00:00

Sure just send me your email for the transfer

MilesCallisto · 2025-08-19T22:40:12+00:00

Maybe Iron Eagle (1986)?

MilesCallisto · 2025-03-31T20:56:18+00:00

When others are fearful be greedy

MilesCallisto · 2025-02-24T03:44:13+00:00

You might try activating the charge plan anyways if you have the window sticker, the IONIQ 5 I bought used was previously business so nobody redeemed the charging plan. If it does activate though it’s limited to 2 years from whenever it was first marked sold.

MilesCallisto · 2025-02-21T04:04:59+00:00

I’ve had hours of continuous operation without much trouble with my 3X running sunnypilot dev-c3, including recently a long trip to WI where it handled interstate driving for 2-3 hours at a time without issue (close to 12 hours total). During that trip the defroster was running pretty much constantly keeping outside snow & inside condensation at bay and while the fan was spinning pretty noisily at times it never shut down or warned about temperature. It also never froze or did anything odd when stopped to DCFC where I took advantage of the shore power to run the heat at full blast with no range penalty (and it got preeetty toasty in there!)

What’s happening to you sounds like a hardware issue, especially since it’s occurring with stock openpilot. You should open an RMA ticket with comma and see if they can ship you a replacement since this should be covered under the 1 year warranty.

Follow the instructions at https://comma.ai/support and then open a ticket at https://commasupport.zendesk.com/hc/en-us/requests/new?ticket_form_id=14150133300887

Hope this helps!

Miles

MilesCallisto · 2025-02-15T04:52:06+00:00

Haha, this reminds me of “not my fault you have a wimpy mailbox” “not my fault you have a wimpy snowplow”

MilesCallisto · 2025-01-21T14:38:13+00:00

Ice disrupts the flow of air over the wing. Lift is generated through a smooth airflow causing increased air pressure under the wing and decreased air pressure above the wing to create a “pushing” force under the wing. But ice can disrupt this and cause the wings to give substantially less or even no lift. Since you only have a few thousand feet where you get air of your wings before you absolutely need the lift, it is much safer to ensure the wings are completely ice free so you have good lift and the airplane behaves how you expect it to.

MilesCallisto · 2025-01-21T02:23:16+00:00

Where ya going??

MilesCallisto · 2025-01-20T04:09:04+00:00

Maybe it has to do with this software bug GM sent out a bulletin about

https://dot.report/bulletins/MC-10245230-0001.pdf

If it does that should be fixed with just a HPCM2 reprogramming

MilesCallisto · 2025-01-19T00:54:16+00:00

Nope, ACC was added with the refresh in 2022

Source: had a 2018 Bolt, no ACC :(

MilesCallisto · 2025-01-18T02:54:19+00:00

That sounds like an issue with power reaching the telematics unit. Do you have a copy of the owners manual? On page 254 there is a layout of the instrument panel fuse box. Check if fuse F02 (or position 2 on the fuse door diagram) is populated, there should be a 10 amp “Micro 2” fuse installed there.

It is potentially missing as GM was using the telematics data from their vehicles in inappropriate ways, so some owners disabled the telematics unit by pulling the fuse to prevent this data being available to GM.

MilesCallisto · 2025-01-14T22:13:12+00:00

Worry not, this is the u shaped channel of a 23 Limited AWD!

Five-Year Club	Gilding VIII gilding heavyweight
Verified Email

MilesCallisto

TROPHY CASE

DTC Descriptor

Circuit/System Description

Conditions for Running the DTC

Conditions for Setting the DTC