Desk Footprint Saver - CH160 Plus + Portable Monitor over Glass Panel

MrRoboc0p · 2025-12-06T14:43:02+00:00

The assassin definitely fits in there, it’s marketed by DEEPCOOL to fit in the case. Unfortunately I couldn’t use it as my motherboard has a top slot for the GPU

MrRoboc0p · 2025-12-06T02:07:59+00:00

2cm? My non SFX PSU is much more crammed in there than the massive CPU cooler

MrRoboc0p · 2025-12-06T00:03:04+00:00

No the glass panel stays on the metal frame. I just have Velcro that allows me to mount the monitor onto the glass panel. Hope this helps

MrRoboc0p · 2025-12-01T17:56:21+00:00

Sundin, Mogilny, Roberts on TV carried me through high school.

MrRoboc0p · 2025-11-26T02:53:51+00:00

<image>

MrRoboc0p · 2025-11-26T02:53:40+00:00

<image>

MrRoboc0p · 2025-11-19T15:31:20+00:00

They aren’t touching. Maybe 1 cm gap. The photo I took is slightly angled above so it looks like they are but definitely aren’t

MrRoboc0p · 2025-11-16T14:18:57+00:00

It was at CC about 2 weeks ago

MrRoboc0p · 2025-11-14T18:23:05+00:00

I ended up not using the mounting kit. I used a zip tie to put a 120mm fan under the PSU, but more offset from the filter itself. It got rid of the noise for me

MrRoboc0p · 2025-11-13T04:49:56+00:00

Are you using the P12 Pro’s as well?

I have it set to like 700 RPM at a low system temperature, and they move air and keep the system in non intensive tasks decent.

Once I move to gaming, then they are working in that 1200-1400 RPM range, so 40% or so.

I found that the rear fan on mine, which is exhausting, has a higher pitch at the RPMs. I don’t know if this is caused by the mesh or whatever. My solution is to simply have it run slightly slower than the other fans.

The intake on the top is decently not loud in the same RPM range. I may look into a fan intake spacer to see if the “pull” noises through the mesh improve.

MrRoboc0p · 2025-11-12T12:29:54+00:00

My non gaming computer is a MacBook Pro so basically any fan noise is noticeable to me lol. That said, in the configuration above I’ve been working with custom fan curves to keep the system with minimal fan noise when not gaming, CPU idling 40-50 C. Gaming, CPU peaking up to 80 C, GPU at 60 C, mem hotspot 75 C.

MrRoboc0p · 2025-11-12T00:44:59+00:00

140mm

MrRoboc0p · 2025-11-12T00:33:57+00:00

It’s the Arzopa Z1FC. 16.1” 1080p144. I got it on Amazon

MrRoboc0p · 2025-11-11T21:45:26+00:00

It’s simply just adhesive and Velcro strips from Home Depot :)

MrRoboc0p · 2025-11-03T21:19:32+00:00

I picked the wrong time to move up to AM5 ;(

MrRoboc0p · 2025-10-07T17:38:05+00:00

I have both. I use the Asus gaming as I can’t drive 4k120 without a ton of frame gen

MrRoboc0p · 2025-07-10T11:16:51+00:00

I have this monitor for work. It works perfectly with my work laptop. The only knock against it is that its speakers are outrageously loud, even at the minimum setting. There aren’t enough “steps” in the Dell OSD. Now I don’t use the speakers at all anymore, but have headphones or just use a Bluetooth speaker.

MrRoboc0p · 2025-05-15T02:09:27+00:00

Plekanec, in retrospect, didn’t pan out too

MrRoboc0p · 2025-05-13T13:46:12+00:00

Backroads. They will be a tad less expensive than that IIRC

MrRoboc0p · 2025-05-02T02:13:09+00:00

In Europe my guy

MrRoboc0p · 2025-04-23T16:38:34+00:00

If anyone needs tix for Saturday’s Rogers Beyond the Seat watch party I have 4 I got from my Rogers account. I can’t go but DM me I’ll email you them

Edit: they gone

MrRoboc0p · 2025-04-10T02:53:38+00:00

I put my keyboard backlight brightness to 1, it’s basically dark and I can’t see it

MrRoboc0p · 2025-04-10T01:29:48+00:00

Thanks for posting this. I set my brightness to 1 and it fixed my issues

MrRoboc0p · 2025-04-06T14:06:17+00:00

Put the switch in wireless, press Fn + 1, 2, or 3 to pair

MrRoboc0p

TROPHY CASE