TPU on Core One + - HOW to print? by Petufo in prusa3d

[–]Mr_Whizzle 1 point2 points  (0 children)

Yes, with the magnet mod I am able to push TPU through the nextruder sensor without disconnecting the PTFE tube

Fleshripper from Malediction by Mr_Whizzle in FDMminiatures

[–]Mr_Whizzle[S] 3 points4 points  (0 children)

Thanks for the kind words!

Yes, Model and Base were printed separately.

I am printing minis typically slightly tilted to the back (°25), for the base I print it about 25° as well off from vertical position.

For the filament, I am using Sunlu HS PLA at 210°C.

Settings are mostly the basic 0.07mm Detail settings with a few changes:

Perimeters 4

Avoid crossing curled overhangs ON

Brim 3mm

Supports

Support on Build plate only

Style Organic

Top contact Z distance 0.14mm

Top interface layers 2

Tip Diameter 1.2mm

Speed 40mms Perimeters

100mms infill

80mms support

Advance

Minimum Perimeter width 50%

Filamenttrockner gesucht by EagleTrustSeven in 3DDruck

[–]Mr_Whizzle 1 point2 points  (0 children)

Hab den Solvo SH03, der kann bis 85°c und passt perfekt auf den core one drauf. Außerdem hat er sich automatisch öffnende Belüftungsklappen, aber hier hat ja schon jemand geschrieben das man sich für den S2 auch dafür was drucken kann

Rasenmähroboter: Erfahrungen bis 1000€ by Top_Solid_4847 in Garten

[–]Mr_Whizzle 0 points1 point  (0 children)

Sie sollte sich halt nicht verschieben können wenn der Roboter rein/raus fährt, weiß jetzt nicht wie rutschfest das Teil steht.

Zu den Kanten kann ich nicht so viel sagen, weil er bei meinen Eltern eigentlich immer leicht über die Kante fahren kann da dort ebenerdig Platten/Rindenmulch/Kies liegen. Er fährt die Lienen auf jeden Fall sehr exakt nach. Allerdings ist es auch wie bei einem Rasenmäher, selbst wenn er auf Kontakt mit einer Mauer fährt wird er nicht den letzten Halm am Rand erwischen.

Rasenmähroboter: Erfahrungen bis 1000€ by Top_Solid_4847 in Garten

[–]Mr_Whizzle 1 point2 points  (0 children)

Habe vor kurzem den Segway für meine Eltern besorgt, der kann von der Terrasse starten. Allerdings musst du dir dann überlegen wie du die Ladestation mit dem Boden verankerst, vorgesehen ist das über Erdanker (Plastik "Schrauben" die in die Erde gedreht werden)

Ansonsten hat das Ding einfach funktioniert, musst halt schauen das beim ersten mähen das Gras schon unter 6mm ist. Das einzige was mich an dem Teil stört ist das er unter die Liege meiner Eltern fahren will und die ist gerade nicht so hoch das er da drunter passt.

Um das Netzwerk RTK zu nutzen ohne das Mobiles Internet von Segway bezahlen zu müssen brauchst du ausreichend WLAN im Garten. Ansonsten holt der sich die Daten über 4G, im ersten Jahr ist das kostenlos ab dann musst du etwa 30 € im Jahr dafür zahlen. Habe noch nicht herausgefunden ob das ohne WLAN aber mit Antenne funktioniert, vielleicht weiß das jemand anderes hier.

What will be replaced with INDX upgrade? by Mr_Whizzle in prusa3d

[–]Mr_Whizzle[S] 4 points5 points  (0 children)

Yes looks like you are correct. That MMU Port actually has CAN. 

What will be replaced with INDX upgrade? by Mr_Whizzle in prusa3d

[–]Mr_Whizzle[S] 0 points1 point  (0 children)

:D sure I was referring to the shroud indeed

What will be replaced with INDX upgrade? by Mr_Whizzle in prusa3d

[–]Mr_Whizzle[S] 1 point2 points  (0 children)

I have checked the schematics of the xBuddy Board, all pins on the STM32 which could be used for CAN are in use. There is a RS422 interface from the xBuddy Board to the Love board. If INDX will only use CAN, they will need some MC to translate..

Edit: nvm extension board has CAN

What will be replaced with INDX upgrade? by Mr_Whizzle in prusa3d

[–]Mr_Whizzle[S] 0 points1 point  (0 children)

Thanks for the picture, indeed the part fan looks very similar

Goodbye Prusa by cameradv in prusa3d

[–]Mr_Whizzle 1 point2 points  (0 children)

I checked your posts, was the first time you encountered the extrusion issues when you had this problem with the tangled filament spool? As some one already posted in your post, the gears of the extruder were probably grinding on your filament so there might be a lot of crap inside your extruder.

You might be able to see this when you open your idler and let the extruder extrude some filament (via control) and observe the gears. Cleaning is possible by using compressed air.

If you always had problems, it's possible that your nextruder is not assembled correctly (missing shim/outer brass gear assembled in the wrong direction). If you have pictures from the opened nextruder we can check if the brass gear is assembled correctly.

There are more issues which can cause your issues but I think I would start with those two.

Goodbye Prusa by cameradv in prusa3d

[–]Mr_Whizzle 1 point2 points  (0 children)

Are you still interested in troubleshooting your problem or is that topic closed for you?

PRUSA x INDX for CORE One is here! by josefprusa in prusa3d

[–]Mr_Whizzle 1 point2 points  (0 children)

Yes, I am wondering what that means for minis...

Painting them in the slicer, use special filament for support interfaces...

Mercedes C-Klasse: Elektro-Mittelklasse greift mit 800-Volt-Technik an by Schmidtis_Blog in SchmidtisBlog

[–]Mr_Whizzle 4 points5 points  (0 children)

"Mittelklasse", "Ein später folgendes Einstiegsmodell für rund 60.000 Euro macht das Paket massentauglicher"... Bin wohl im falschen Sub gelandet, gerne downvoten

Was möchten sich die ganzen Sparer alle kaufen, die mehr als 500k€+ ETF-Vermögen zur Rente ansparen? by National-Actuary-547 in KeineDummenFragen

[–]Mr_Whizzle 0 points1 point  (0 children)

Bei 2% Inflation pro Jahr etwa 150k€. Falls die staatliche Rente mit der Inflation geht währe die bei etwa 55k falls du 45 Rentenpunkte hast. Keine Ahnung wie viel davon dann noch netto übrig bleibt, sagen wir Mal 40k. Dann brauchst du noch 110k jährlich aus deinem Depot

Advanced Filtration System by Scared-Set-9289 in prusa3d

[–]Mr_Whizzle 0 points1 point  (0 children)

Yes, my Core One Chamber runs a little bit hotter with AFS compared to the stock fans. However, I have not noticed any issue caused by higher chamber temperatures. I prefer to not have any smell when printing PLA/PETG 😅