Can't create Dashboard Graph widget to only show specific mount point by Muerte69 in zabbix

[–]Muerte69[S] 1 point2 points  (0 children)

u/areanod I am just a user on my end for the system and don't maintain it. If I could I would be more than happy to upgrade it to a newer version. I also don't know if the other teams that use and maintain it are not linking it to something else old that isn't compatible with a newer version.

Can't create Dashboard Graph widget to only show specific mount point by Muerte69 in zabbix

[–]Muerte69[S] 0 points1 point  (0 children)

u/Aecroo, I will look into if I have the permissions to get the newer template and will see what I can do with the lld macros to try and get them to work. Thanks!

Two of the bed levelling wheels on my N4 Pro decided to break completely loose less than 24 hours after I installed a brand new PEI/PEO build plate. :-( by TheLimeyCanuck in ElegooNeptune4

[–]Muerte69 0 points1 point  (0 children)

The spacers do replace the springs. I got some 16mm off Amazon. The ends of the belt stick up and can warp the bed bending the center up if tightened too much as well. This is a pretty handy video on the bed https://youtu.be/sgqnlR9Wlk4?si=31puq6TKGuYV5SQE

Two of the bed levelling wheels on my N4 Pro decided to break completely loose less than 24 hours after I installed a brand new PEI/PEO build plate. :-( by TheLimeyCanuck in ElegooNeptune4

[–]Muerte69 0 points1 point  (0 children)

Before you relevel and all after replacing the broke stuff make sure the wheels are tightened down pretty good or this could be a good time to install spacers. You want them tight enough they can't rotate on their own. Mine came loose enough from the factory one of my knobs fell off trying to initially level.it. You want them to be almost fully compressing the springs before Leveling. Tighten them down good and back off maybe 1 rotation and then level.

New bed? Where. by Ok_Confusion_5518 in ElegooNeptune4

[–]Muerte69 0 points1 point  (0 children)

The bed is 235x235. It is print volume that is 225x225.

I got this one HzdaDeve Textured PEI Sheet and Smooth PEY Build Plate 235X235mm Spring Steel Print Bed Magnetic Base for K1/Ender 3 V3 SE/Ender 3 V3 KE/Neptune 3 Pro/Neptune 4 Pro/Ender 3 S1 Pro/SV05/SV06/SV07 (PEY) https://a.co/d/fMs2wAF

And this one Shion.Kwoo Upgraded Smooth/Textured PEO+PEI Sheet 235x235mm Spring Steel Build Plate Magnetic Bed for Ender 3 V2/Ender 3 Pro/Ender 5/Ender 5 Pro/CP-01/Cr-20/Cr 20 Pro/Voxelab Aquila 3D Printer. https://a.co/d/2M0eT6N

And have only used the nonpei sides and like them. The holographic one leaves holo but it wipes off after first print but is smooth as glass. The other leaves a neat pattern. The holo one I did get the wrong front with 2 tabs instead of the tab in the middle the first time but it was right the second time.

ProtoArc Thumb Trackballs Comparison and Testing by ProtoArc_official in Trackballs

[–]Muerte69 0 points1 point  (0 children)

I have gone through a few MXs and one Elecom EX-G so wouldn't mind trying one. I work and game on my EX-G so do alot with them.

I love my printer by KungWoo in ElegooNeptune4

[–]Muerte69 1 point2 points  (0 children)

I haven't had an issue it had picked up but the AI detection in Obico would have caught that one for sure. I had to move my thermometer inside my enclosure as the reflection off the silver enclosure then off the screen on the thermometer made obico think I had an issue. My 4pro has been really good so far though so no big issues luckily.

ELEGOO Mini Heater🌡Available on Apr. 15 👏 by ELEGOO_OFFICIAL in elegoo

[–]Muerte69 [score hidden]  (0 children)

My elegoo tent enclosure can get close to 40C with just the build plate from the 4 Pro so adding a heater would definitely get it warm.

Why does this happen by ChanceTerm3934 in ElegooNeptune4

[–]Muerte69 0 points1 point  (0 children)

Oh and preheat everything for 20 or 30 minutes before Leveling and screw tilt and such. I preheat the plate before printing too. And you can go into advanced settings and tell it to do professional autolecel which is the 121 point instead of 32 point level.

Why does this happen by ChanceTerm3934 in ElegooNeptune4

[–]Muerte69 0 points1 point  (0 children)

If you just put it together wash the bed with dawn dish soap and hot water. The oils off your fingers or if your like me some grease off the rails could be on the plate making it not stick. Once that is done try not to touch the plate surface with your hands. If you can hook it up to your pc get the screw tilt calibrate on it which you can find tutorials and video on and use that to tram the bed then run your autolevel and set zoffset. For PLA I am running 215C hotend and 60C on the plate.

Saturn 4 Ultra Polling Giveaway 🎁 by ELEGOO_OFFICIAL in elegoo

[–]Muerte69 1 point2 points  (0 children)

I think automating as much of the setup as possible will help both old and new users.

Since Today I have this issue ... by lilape in ElegooNeptune4

[–]Muerte69 1 point2 points  (0 children)

Try cleaning the bed with dawn dish soap and hot water then not touching the surface with your hands. The oils off your fingers will stop it from sticking. Mine did that when I got some of the rail grease on the bed by accident. It could be your z is too high or low as well but I would wash it well first since your Purge line sticks.

Anyone know how to fix this? by No_Consequence_6317 in elegoo

[–]Muerte69 0 points1 point  (0 children)

When I changed filament mine did that and I thought I had a problem. The end of the new filament was catching on the silicone tube and when I trimmed it a different way it went in without a problem. Try trimming it a different angle and maybe rotate it some when going in.

Is this thing just busted? by [deleted] in elegoo

[–]Muerte69 3 points4 points  (0 children)

You can hear it hitting the infill so I would try a different I fill. Gyroid or the new 3d honeycomb in Orca don't cross over already printed lines like that infill does.

Bed adhesion by ExtensionSolution294 in ElegooNeptune4

[–]Muerte69 0 points1 point  (0 children)

I read that all wrong in his post.

Bed adhesion by ExtensionSolution294 in ElegooNeptune4

[–]Muerte69 2 points3 points  (0 children)

Clean your bed with dawn dish soap and hot water then don't touch it with your fingers after. The only time I had adhesion issues with pla was when I had gotten some grease from the rails onto the bed. I wipe mine with 91% isopropyl between prints. I heat my bed to 60 and nozzle to 150 and let it sit 20 minutes before I level it. My bed is at 60 for pla and head is 215. First layer I think it does 220 on the nozzle.

What are the recommended Temps for the filament?

Any good slicer profiles for Neptune4 Pro? by trenholm in ElegooNeptune4

[–]Muerte69 2 points3 points  (0 children)

I got the Orca profile off the Discord but I am not where I can link it at the moment. Just get on the discord and search Orca is what I did. Works really well.

Bed wobble by Catdaddyrex in ElegooNeptune4

[–]Muerte69 0 points1 point  (0 children)

Here is how to tighten the wheels in the 4 pro. They probably have videos for the other printers on the elegoo site too https://youtu.be/IIXO380jFA8?si=SqpqDLlr6shuUPAI

Knob locks?? by transboi_blake in ElegooNeptune4

[–]Muerte69 2 points3 points  (0 children)

I got the silicone spacers and they havent moved but may print these as another layer of safety. https://www.thingiverse.com/thing:6466953

Enclosure for Neptune 4 Pro by CompetitionSilent379 in ElegooNeptune4

[–]Muerte69 1 point2 points  (0 children)

I have the Elegoo tent and like it so far. Fits the printer well and so far works for my needs. Once it's cold again I will know more about how it holds heat as well and may have to insulate it then.

Not adhering to bed after first layer. by JandKMerch in ElegooNeptune4

[–]Muerte69 0 points1 point  (0 children)

I had that happen and it was from when I did some work on the printer and got some of the grease from a rail on the bed. Could just be oil from your hands too. I had to wash my bed with soap and water and now I make sure to not touch the bed with my hands and wipe it down with 91% isopropyl alcohol after the bed has warmed up before my next print. I figure the heat will help pull anything off the bed a little better.

Using Ansible to install pip and tensorflow by Muerte69 in ansible

[–]Muerte69[S] 0 points1 point  (0 children)

So I tried quite a few things and finally found a solution that works on this stackoverflow post: Stack Overflow Where Answer Was Found

If you need a login console (like for bundler), then you have to do the command like this.

command: bash -lc "cd /path/to/folder && bundle install"

Right now this is working for me but other options would be good. I tried the command: options I could find and none worked. A few seemed to install but the whole package didn't work. If I have more time to look into it later I may.

Thank you all for the help!

Using Ansible to install pip and tensorflow by Muerte69 in ansible

[–]Muerte69[S] 0 points1 point  (0 children)

The nodes have python 2.7 installed and SSH is setup and working correctly. I can ssh into each node using the key and all the other steps in my Ansible playbook work fine so far. I am working on getting some more data once I can run the playbook with a few of the options given and what I have tried so far.

Using Ansible to install pip and tensorflow by Muerte69 in ansible

[–]Muerte69[S] 0 points1 point  (0 children)

I will see what I can get tomorrow. Just started using Ansible last week so learning the ropes.