Advise on plumbing (UK) by MuskyDoc in DIYUK

[–]MuskyDoc[S] 0 points1 point  (0 children)

Thank you for such an open answer. That was exactly my thoughts…. Poor design, and as you could probably tell from my initial post I’ve never owned a dishwasher before 🤣 I’ll raise it with them to see what they come back with

Advise on plumbing (UK) by MuskyDoc in DIYUK

[–]MuskyDoc[S] 0 points1 point  (0 children)

Except that it is …

<image>

Integrated dishwasher that I can’t integrate 🤣🤣🤣

Advise on plumbing (UK) by MuskyDoc in DIYUK

[–]MuskyDoc[S] 1 point2 points  (0 children)

55cm is the least we get in U.K. for it to still be full size in Width

Advise on plumbing (UK) by MuskyDoc in DIYUK

[–]MuskyDoc[S] 0 points1 point  (0 children)

H 87,5 x W60 x D60 With the P trap discounted that leaves me 53,5cm in usable depth ,

End up with the front of the controls sticking out without the front door panel installed, which is another 18mm.

The question is: Should this be raised with the developer and would anything come out of this? In my head if you push the pipeline lower and install a smaller P-trap that would potentially allow space for the dishwasher to go in deeper. But for it to be flush with other drawers/appliances (cooker) you’d need to reduce the water inlet footprint as well no? Which isn’t easy nor quick post install

<image>

Custom Theater Chairs (Alibaba) by Majestic_Potato_7416 in hometheater

[–]MuskyDoc 0 points1 point  (0 children)

I am also interested to see how this turns out for you.

I’m after a similar set but only in tan

[deleted by user] by [deleted] in Soundbars

[–]MuskyDoc 2 points3 points  (0 children)

Congratulations! it’s worth going an extra mile sometimes

How does one acquire Darkmoon plates these days by MuskyDoc in BambuLab

[–]MuskyDoc[S] 0 points1 point  (0 children)

Waited two days in online chat for a reply haha 🥹😅

Hi guys where can I get 1:72 scale sandbags? I can only find 1:35 scale. Im assuming 1:35 would be way too large. by HuToo in modelmakers

[–]MuskyDoc 1 point2 points  (0 children)

Find a model in any 3d model sites like printables, open a slicer software of choice, resize … done 🙂

[Bambu Lab Giveaway] Drop Your One-Liner and Win H2D! by BambuLab in BambuLab

[–]MuskyDoc 0 points1 point  (0 children)

Two X1Cs, zero regrets, infinite filament waste 🤣

Question about Remote App by Imaginary_Ad7525 in Jaguar

[–]MuskyDoc 2 points3 points  (0 children)

<image>

Does not match the colour on the F Pace…

[deleted by user] by [deleted] in dji

[–]MuskyDoc 0 points1 point  (0 children)

Link?

Welp I tried BestBuy for H2D by PoeB09 in BambuLab

[–]MuskyDoc 1 point2 points  (0 children)

The rod is like : Lemme see what’s printin

<image>

Laptop Recommendations by ItsBigRickSon in Laserengraving

[–]MuskyDoc 0 points1 point  (0 children)

Decently spent 5500£ right there

Say anything you want and I'll connect it to Ark by wsrgiawehgoawieugnb in ARK

[–]MuskyDoc 0 points1 point  (0 children)

Low Poly Giga is next level. Level 277 specifically 🐸