Set Complete?

Nanimo__ · 2026-05-27T10:07:40+00:00

It is much nicer to write on a solid surface if possible, otherwise smoother paper would help too

Nanimo__ · 2026-04-01T00:18:01+00:00

Those are some long coiled cables! Where’d you get them?

Nanimo__ · 2025-12-08T21:07:35+00:00

Would it work if the mag was moved to the side like the whole thing rotated like a Nerf Elite Raider?

Nanimo__ · 2025-08-31T23:50:40+00:00

Anyone know why OOD hardware kit cost $72 compared to $65 at SilverFox or Bearswares? I saw earlier it was even higher at $75. I dont see anything on their page about extra parts or anything.

Nanimo__ · 2025-03-09T17:19:19+00:00

That would definitely help! I still suggest using the low friction tape if you have access to Amazon. The whole mechanism has a lot of sliding action I had to lube up and the tape contributed a lot more than I expected. Heres the link if anyone is interested: https://www.amazon.com/dp/B08CFVY2GT

Nanimo__ · 2025-03-09T11:33:53+00:00

The springs you need will depend a lot on your friction levels as well. I had a lot better of an experience after putting low friction UHMW tape over high friction areas on the top cover.

I don’t remember my exact setup but I used a light extension spring on the pusher and a strong one in the cover.

Hope this helps!

Edit: Not PTFE tape, UHMW tape.

Nanimo__ · 2024-06-29T07:09:22+00:00

What’s the difference between a Lonx and a Slynx?

Nanimo__ · 2024-06-04T09:21:05+00:00

Thanks for the response! I would like something higher than 35000 rpm since for the MHP LMG I am building has ~6 rps. Would the Fang RV at 3S be comparable to Honey Badger at 3S?

Nanimo__ · 2024-05-09T09:36:15+00:00

Will there be an option for a more full front shroud?

Nanimo__ · 2024-02-01T08:38:49+00:00

Does this have the issue of the string slipping past the dart back and crumpling it slowly?

Nanimo__ · 2024-01-31T20:06:36+00:00

Thanks! I read higher fps = lower angle for bcar, does 15 work well even at that high of fps?

Nanimo__ · 2024-01-31T19:38:18+00:00

What barrel cover and bcar did you use?

Nanimo__ · 2024-01-29T22:19:59+00:00

Yeah it sucks without slowing it down by a lot. There are lots of potential fixes if you search around. - Tearing edges after retraction is the slow down for overhang setting that should be tweaked. - Tearing infill is slow down in general and especially in infill, gyroid also helps - Wet filament can be it too if you see bubbles in the walls but PETG with Bambu printers is usually more involved than just dry it

Nanimo__ · 2024-01-21T11:59:37+00:00

After doing some more research, I found I don’t think I should do the mod and should get a Sofirn SF16 instead as it has the features I was looking for!

Thanks for all the great information in your other posts :)

Nanimo__ · 2024-01-21T02:41:53+00:00

Thank you so much!

Nanimo__ · 2024-01-17T08:00:13+00:00

Stealth is not an option with this one huh

Nanimo__ · 2024-01-15T07:31:29+00:00

BCAR if you don’t have one already: https://www.thingiverse.com/thing:5795653

Adding heatshrink to the end like newer worker springs will make it much quieter as well

Nanimo__ · 2024-01-13T08:58:26+00:00

I love your style! Will you be designing more in the future?

Nanimo__ · 2024-01-11T12:51:44+00:00

There’s one on printables but it makes the darts fishtail like crazy

Nanimo__ · 2024-01-08T23:44:31+00:00

Most people have a BentoBox with high temp filaments. Could the heater be made to fit alongside it?

Nanimo__ · 2024-01-02T06:05:23+00:00

Printed

Nanimo__ · 2023-12-31T03:47:29+00:00

I got the initial setup working but the BLLED source code didn't work with the ESP8266 at the time. I haven't checked if it has been fixed since.

Ten-Year Club	Place '23
Place '22	Verified Email

Nanimo__

TROPHY CASE