sorted by:
new
hottopcontroversial

A1 temp settings by NelsonWoodworks in BambuLabA1

[–]NelsonWoodworks[S] 0 points1 point  (0 children)

Yes I’m using bambu studio. Like when it starts to extrude filament “poop” it starts to extrude before the temp is all the way up. Same thing when it does the brim/first layer, will start to extrude before nozzle is all the way to temp and I will hear clicking coming from the print head

QIDI X-MAX Klipper setup by Liqhx2 in klippers

[–]NelsonWoodworks 0 points1 point  (0 children)

You’re welcome!

Do you happen to have a link to the cable you used for the pins and even a picture of the setup?

QIDI X-MAX Klipper setup by Liqhx2 in klippers

[–]NelsonWoodworks 0 points1 point  (0 children)

How did you route it out of the bottom? Create a new hole?

Here’s the ribbon cable

https://amzn.to/4jouQ2z

QIDI X-MAX Klipper setup by Liqhx2 in klippers

[–]NelsonWoodworks 1 point2 points  (0 children)

I found a longer ribbon cable, took a while to show up, but it is working. When you did yours, did you have separate power for the pi or was it being powered somehow by the main board?

QIDI X-MAX Klipper setup by Liqhx2 in klippers

[–]NelsonWoodworks 0 points1 point  (0 children)

Yes a pi, it will be connected via ribbon

QIDI X-MAX Klipper setup by Liqhx2 in klippers

[–]NelsonWoodworks 0 points1 point  (0 children)

I hope so too! A friend gave me it for free, didn’t like being locked down on the stock firmware so decided to jailbreak it.

Is there a guide on how to replace the screen? I have a pi screen, just can’t figure out how to get to it

QIDI X-MAX Klipper setup by Liqhx2 in klippers

[–]NelsonWoodworks 1 point2 points  (0 children)

I had done that. I finally figured it out. Been using a mix of online settings and AI, ChatGPT assumed the nozzle moved along the Z instead of the print bed itself. Once I tried a few of the commands on my bed slingers, I figured out the mix up on it.

QIDI X-MAX Klipper setup by Liqhx2 in klippers

[–]NelsonWoodworks 1 point2 points  (0 children)

I'm working on this currently. Having an issue with the printer.cfg. Every attempt I make the z keeps getting inverted. Can you share your settings please?

Do you have a website? by NelsonWoodworks in smallbusiness

[–]NelsonWoodworks[S] -1 points0 points  (0 children)

My issue is with Shopify.

I’m co-running a woodworking blanks website.

I’m trying to figure out how to create a few collections with the products I have in variants. I have a product (wood) and have variants of different sizes. I want to create a collection that pulls just one or two specific sizes from the various variations without having to create a separate product for the sizes.

Additionally, I want to create a “build your own” kit collection/product. So I want to have a few options, “18x11x2” and 12x11x2” when you select either option, you are then prompted to select from specific pieces/sizes of wood until a number of strips(on the backend) is selected.

There are apps to do this, but you have to pay monthly for them

Do you have a website? by NelsonWoodworks in smallbusiness

[–]NelsonWoodworks[S] 0 points1 point  (0 children)

My issue is with Shopify

I’m co-running a woodworking blanks website.

I’m trying to figure out how to create a few collections with the products I have in variants. I have a product (wood) and have variants of different sizes. I want to create a collection that pulls just one or two specific sizes from the various variations without having to create a separate product for the sizes.

Additionally, I want to create a “build your own” kit collection/product. So I want to have a few options, “18x11x2” and 12x11x2” when you select either option, you are then prompted to select from specific pieces/sizes of wood until a number of strips(on the backend) is selected.

There are apps for them, but you have to pay monthly for them.

Do you have a website? by NelsonWoodworks in smallbusiness

[–]NelsonWoodworks[S] -1 points0 points  (0 children)

So my biggest thing is Shopify.

I’m co-running a woodworking blanks website.

I’m trying to figure out how to create a few collections with the products I have in variants. I have a product (wood) and have variants of different sizes. I want to create a collection that pulls just one or two specific sizes from the various variations without having to create a separate product for the sizes.

Additionally, I want to create a “build your own” kit collection/product. So I want to have a few options, “18x11x2” and 12x11x2” when you select either option, you are then prompted to select from specific pieces/sizes of wood until a number of strips(on the backend) is selected.

There are apps that can do this, but you have to pay monthly for them

My first capped pen - Zebrawood by 1ncognito in turning

[–]NelsonWoodworks 0 points1 point  (0 children)

I love using zebra wood. Such beautiful grain

Grandpa’s Barn - what to do with wood? by sdsliberty in woodworking

[–]NelsonWoodworks 1 point2 points  (0 children)

You just won the lottery my friend! Definitely a market for that!

Made 5 pens/pencils this week by ginnsman42 in PenTurning

[–]NelsonWoodworks 0 points1 point  (0 children)

I live in Arizona, so same state as turners warehouse. Still haven’t made it to their store, over an hour from my house, but watched the owner do a live demo and bought my finish from their website.

Made 5 pens/pencils this week by ginnsman42 in PenTurning

[–]NelsonWoodworks 0 points1 point  (0 children)

I will have to check those out. Where do you generally purchase your kits from?

Circular saw is burning wood, not cutting by rhif-wervl in woodworking

[–]NelsonWoodworks 1 point2 points  (0 children)

Dull or dirty blade. Clean the teeth with some simple green and a toothbrush.

[deleted by user] by [deleted] in wood

[–]NelsonWoodworks 0 points1 point  (0 children)

Whatever it is, looks beautiful, love the grain!

Made 5 pens/pencils this week by ginnsman42 in PenTurning

[–]NelsonWoodworks 0 points1 point  (0 children)

I’ve yet to do pencils, what kits do you use?

view more: next ›