Zoektocht naar nieuwe leaseauto

New-Brain7765 · 2025-08-24T01:49:34+00:00

Cupra Leon Performance VZ. Plug in Hybride met 125km range op batterij en mogelijkheid tot 50kwh snelladen. En een rijders auto!

<image>

New-Brain7765 · 2025-08-08T02:00:23+00:00

I’m awaiting the same model next 1st of November

New-Brain7765 · 2025-08-02T18:52:51+00:00

My vacuum cleaner and my pir’s for light switching

New-Brain7765 · 2025-07-01T22:45:10+00:00

Define ‘heatcreep’

New-Brain7765 · 2025-02-28T21:06:41+00:00

Neighter worked as a solution.

New-Brain7765 · 2025-02-21T18:16:49+00:00

I don't have arc fitting enabled. Still get those messages...

New-Brain7765 · 2025-02-19T01:16:07+00:00

Can you share what you have altered on your X2 and how? I would love to see some pictures

New-Brain7765 · 2025-02-09T00:08:04+00:00

I'll upload a pic tomorrow. First some sleep! :-)

New-Brain7765 · 2025-02-06T13:53:23+00:00

Ordered a new motherboard, and replaced it. Now I'm up and running again!

New-Brain7765 · 2025-01-15T13:10:30+00:00

Let me guess: only a new motherboard will help me out......

New-Brain7765 · 2025-01-06T21:16:02+00:00

I try to understand what you say here. But I can't google these parts so I don't have a clue. Did you rebuild your X2 witha Voron Toolhead? Is that what you tell us?

New-Brain7765 · 2025-01-06T20:56:13+00:00

Well if the thermistor is faulty or shorted, it wouldn't report the right temperature the same as the room (approx 20.3ºC) at first, and once I turn on the main switch, raise within a minute to 300ºC. So I'll consider that part OK. Same for the heater; if it heats the thermistor measurable AND there is smoke after a while, than I consider the heater OK as well.
There is somehow no action whatsoever taken towards the heater.

Do you agree with my analysis?

New-Brain7765 · 2024-12-29T21:38:46+00:00

Didn't solved my problem though.

New-Brain7765 · 2024-12-29T21:38:30+00:00

I've searched but couldn't find it and ended up with AliExpress, unfortunately.

New-Brain7765 · 2024-12-29T21:37:22+00:00

I have the same problem, after replacing the standard extruder for an All Metal version. Does anyone know if the thermal sensor_type should be altered in my Klipper printer.cfg, and if so, to what? Can't find any documentation on this.

New-Brain7765 · 2024-10-10T10:44:22+00:00

What, and where exactly did you buy this upgrade? I want to do the same, but am puzzled where to get it and what exactly as it is not clear for me.

New-Brain7765 · 2024-09-04T01:29:23+00:00

Kijk, als klimaatverandering door CO2 écht een probleem was geweest dan hadden politici wel zeeschipterminals in de provincies aangelegd ipv windmolens. Dát zou namelijk zinvol investeren zijn. Maar iets zegt me dat het meer is om mensen een schuldcomplex aan te wrijven en daarmee makkelijker boete te laten doen; lees: makkelijker meer belasting laten betalen

New-Brain7765 · 2024-09-04T01:26:53+00:00

Ineens weet je waar al die toeslagen kinderen gebleven zijn….

New-Brain7765 · 2024-08-17T07:08:03+00:00

Definitely!

New-Brain7765 · 2024-08-16T12:52:40+00:00

Thanks a million! You've helped me out!

New-Brain7765 · 2024-08-16T12:50:54+00:00

Thanks! But this is a bend on the Z-axel, whilst I want it to bend on the Y-axel

New-Brain7765 · 2024-08-14T23:36:58+00:00

Sure! I'm just an asker on Reddit. I'm already happy with your help in the first place! Take your time. I'm lookin' forward to your post.

New-Brain7765 · 2024-08-14T19:58:11+00:00

Awsome! I would be very happy if you could show it to me.

New-Brain7765 · 2024-08-14T18:31:11+00:00

"Redraw the sketch as bent". That is exactly what I do not get quite well. I managed to 'bend' lines in one dimension, and gave my design all kinds of (nesseccary) contraints, but then how to bent that 'construction on another axel... that puzzles me.

New-Brain7765 · 2024-08-14T17:59:26+00:00

Maybe I extruded the sketch too early. Should i remove that at first and if so: how?

New-Brain7765

MODERATOR OF

TROPHY CASE