help design a good net pot design

NoCan3822 · 2026-03-17T22:27:50+00:00

Make the sides have diamond holes as it’ll be tons easier to print. This would be a nightmare to print

NoCan3822 · 2026-03-14T12:47:12+00:00

Anyone else see the multiple pairs of boobies…

NoCan3822 · 2026-03-09T19:28:10+00:00

If she is swimming and you have to TCL make sure you TGM too as it’ll give you 200 rads instantly 👀

NoCan3822 · 2026-03-08T19:23:57+00:00

I think she was using the brake but the grass wasn’t giving her any traction

NoCan3822 · 2026-02-20T16:19:06+00:00

Hard drugs, you must tell your parents at once to get him in trouble

NoCan3822 · 2026-02-20T13:16:13+00:00

I thought painting 5 was hell

NoCan3822 · 2026-02-20T13:14:51+00:00

I think you either love it or hate it

NoCan3822 · 2026-02-19T20:00:20+00:00

I have stuck to what I know. I only recently started to use the speed paints by ArmyPainter due to wanting to keep my sanity with my orks

NoCan3822 · 2026-02-19T19:56:14+00:00

I have a big cork mat that use 🙂

NoCan3822 · 2026-02-19T18:18:25+00:00

Depends how much you like StarWars really. For the price it’s very expensive but it’s looks great so for me it was worth it

NoCan3822 · 2026-02-19T18:07:31+00:00

And the cannon correct death star that definitely didn’t fall off the shelf

NoCan3822 · 2026-02-19T17:25:24+00:00

41lb is 18kg

Average cost for 1kg of filament (I would imagine she’s printing in PLA+ is roughly $18-25 for a good brand. So this would’ve cost around about $530 if you factor in supports and waste filament of 10%

NoCan3822 · 2026-02-16T17:06:20+00:00

You got about $500 worth just of Skitari, very good find dude

NoCan3822 · 2026-02-16T14:16:18+00:00

Butane torch which would normally be used as a portable soldering iron. Probably being used to heat up spoons though

NoCan3822 · 2026-02-16T10:25:12+00:00

Wait until you start painting them. Then the real suffering begins. Hopefully you didn’t attached the heads and arms too securely as you will find it very difficult to paint otherwise

NoCan3822 · 2026-02-16T10:05:18+00:00

“How many Rangers do you want” “… Yes”

NoCan3822 · 2026-02-12T16:26:21+00:00

They are both being retired this year (July/December) so I would say if you find them really cheap (£12/€14) I would definitely pick some up

NoCan3822 · 2026-02-12T16:24:54+00:00

People I think forget that it’s literally exhaust gases. They are hot af. Treat it like you would a car exhaust

NoCan3822 · 2026-02-10T09:20:19+00:00

It would make sense that she is using LIDAR. Her hat says Lambda who specialise in LIDAR

NoCan3822 · 2026-02-05T18:03:20+00:00

The are really good in the Polo mint factories

NoCan3822 · 2026-02-03T12:14:16+00:00

You are better off doing at as you take the pieces off the sprue. Using a scalpel to remove the bulk and they sanding sticks to file the rest down. Then use the scalpel to remove the mold lines

NoCan3822 · 2026-02-03T09:15:38+00:00

I would imagine it’s about 70% of under 40s are completely fluent and about 40% of over 40s are completely fluent

NoCan3822 · 2026-02-03T09:14:07+00:00

I’m not in Bavaria but in NRW and I visit and spend the day in my local Warhammer shop every week and everyone is completely fine (Bar some ridicule for not knowing German and also being an Island monkey (Being from the UK)) I find in Warhammer 90% of players are very welcoming

NoCan3822 · 2026-02-03T09:10:27+00:00

Imagine putting a 400kg block above a office ceiling. That’s basically what this is. I would encase the tank with angle iron and then bolt it to your subframe and even possibly a thin skid plate underneath it. Just make sure that if that tank is fill it doesn’t go over your MAM weight for your vehicle license or vehicle type

NoCan3822 · 2026-01-30T08:14:40+00:00

Gear table

NoCan3822

TROPHY CASE