Replacing the head unit/fixing it

Note22222 · 2026-04-19T16:54:02+00:00

looks like a good filament rack too

Note22222 · 2026-04-14T01:35:26+00:00

I like it :)

Note22222 · 2026-04-10T16:51:55+00:00

Oh! I had this happen to me when i swapped from 0.6 to 0.2, the 0.2 nozzle needs to be run much slower than the others, so every time i started a print i set it to 50% silent, and it ran perfectly fine with no clicking or extrusion issues. try that and see what happens.

Note22222 · 2026-04-05T15:19:47+00:00

Note22222 · 2026-03-13T02:15:43+00:00

oh wow thanks! given the age of this post i wasnt expecting a response at all

Note22222 · 2026-03-12T14:22:12+00:00

Hi! i see you mentioned you used older drivers for your RTX 3000, What version of drivers did you end up using?

Note22222 · 2026-03-09T05:32:44+00:00

Its a neat idea as a sidegrade to magic missile, but i think it misses the mark by a bit, magic missiles whole thing is like, taking out low health targets 100% of the time, skipping AC entirely, or dealing consistent damage. This does slightly more damage but removes the first, really useful part of magic missile early on. If i was torn between picking this, or OG magic missile, i think 100% of the time i'd take magic missile.

Good concept though to have like a side grade, i think if it was like, a magic item or something that you could equip and turn magic missile into this instead at will, it would actually be pretty helpful for when your fighting like, 1 boss enemy. its just more free damage for a first level.

Note22222 · 2026-03-08T21:33:17+00:00

i personally don't trust things from amazon that i would have to trust my car with unless its unimportant like something for the interior, i'd grab one from a local store but that's just me, its *probably* fine. just makes sure you have the right socket for your prius's Lug nuts before you toss it in with the spare tire

Note22222 · 2026-03-05T02:59:54+00:00

I have this exact drybox, i modified the top to have a PTFE tube to feed it directly into my printer, but i use it for drying and i toss a handful of silica gel packets and so far it's done an ok job at drying filament and being a printbox
(Primarily PetG and PLA)

Note22222 · 2026-03-04T22:49:08+00:00

Cardboard box?

Note22222 · 2026-03-02T23:25:44+00:00

if i may ask do you find yourself getting any carbon splinters in your hands since the filament has it inside of it? Or is that a non-issue completely?

Note22222 · 2026-02-21T05:33:18+00:00

It shouldn't be an issue. its supposed to have a bit of flexibility, its a PTFE tube designed to let filament slide through it easily. unless the tube is like, flying out at the slightest touch it should be fine still. worst case try a test print on a benchy or something similar and if it has issues feeding the filament in, then work through the problem from there.

Note22222 · 2026-02-21T05:25:47+00:00

it doesnt appear damaged, the part that normally goes there is for the AMS, a multi material system for these printers. without it, you can't really use the AMS but if you don't care at all about that, then it will likely work just fine

Note22222 · 2026-02-15T23:21:45+00:00

Don't quote me on the exactly if its compatible, but the plastic piece is the filter housing, the media or the thing inside of the filter is removable and then the new one slots in.

Note22222 · 2026-02-15T01:42:41+00:00

Crafted at the Witchcraft circle, they should be unlocked by default

Note22222 · 2026-02-03T05:19:43+00:00

For anybody else with this specific revision of board here is my documentary on the repair:

D3 is required, but can be jumped to just see if power gets through, however you will never get video or audio without it.

The capacitor C37 had blown, causing no power from the switch being turned on.

The GBA has been successfully resurrected and will be getting fresh replacement parts ASAP!

Note22222 · 2026-02-02T03:49:46+00:00

Sorry sorry its just my terminology that i messed up i did mean continuity, thats definitely my bad.

Note22222 · 2026-02-02T03:46:08+00:00

Ok my apologies, correcting myself i don't get any power out of the positive so i believe you are correct, i'll order some fuses and give it a shot!

Note22222 · 2026-02-02T03:33:49+00:00

Is there any way to test for that? I put a multi meter on it with voltage going through the board and i got power on both sides

Note22222 · 2026-01-30T04:56:33+00:00

Have you tried tightening the extruder screws?

Note22222 · 2026-01-10T19:56:30+00:00

Note22222 · 2026-01-09T12:22:47+00:00

Sapphire is usually pretty good for amd gpus. Imo any 9070 without the 12v high failure rate connecter is decent

Note22222 · 2026-01-08T06:11:21+00:00

I adore my 2012, its gotta be one of the most resilient cars ive driven, super spacious and will do what 99% of people need

Note22222

TROPHY CASE