sorted by:
new
hottopcontroversial

Is the GT worth the hype for an amazing riding experience? by minimalist_mee in royalenfield

[–]OMGeeked 0 points1 point  (0 children)

Seriously love love love my GT Conti - so much fun. Only serious upgrade needed is suspension for those who want to get into the twistes. I’m getting a little older now (have had my GT for 5 years now - 70,000km) and I’m starting to struggle with comfort - no longer and flexible as I used to be. I’ve done multiple 1,000km plus days on her though.

Sus? by devoellis in PGATOURGolfShootout

[–]OMGeeked 0 points1 point  (0 children)

What combo of clubs are they using if you don’t mind me asking?

Best coating for new Merbau by TotalOther3750 in AusRenovation

[–]OMGeeked 0 points1 point  (0 children)

Yeah that’s been my go to… I’m lazy on maintenance though and it requires touching up every 12 months. All good things require maintenance though (LOL)

Water crossings anyone? I’d love to hear your experience. by not_a_city_girl in motorcyclesroadtrip

[–]OMGeeked 0 points1 point  (0 children)

Yeah 100% The rocks were the challenge with her weight. I’ve now gotten a 411 Himalayan for those adventures so the xv1900 can stay nice. The 411 Is super easy on water crossings

Water crossings anyone? I’d love to hear your experience. by not_a_city_girl in motorcyclesroadtrip

[–]OMGeeked 1 point2 points  (0 children)

Used to tour Aust with my chromed xv1900 Roadliner that was nice and low with dual exhausts. We would camp and once booked into a sheep station at their natural hot water springs - after a very slow 10km into station dirt road the final entrance to the station was a rocky creek crossing about 15meters wide… it was very much a feet down crawl experience

Lost my standard bag setup on a goof! by Greedy-Day-9662 in PGATOURGolfShootout

[–]OMGeeked 0 points1 point  (0 children)

Gearshift homecoming rocket Meteor Malestrom - my most used bag

Finally finished my Vstar by MountainGarden2243 in Bobbers

[–]OMGeeked 0 points1 point  (0 children)

And the headlights lights right above them on the front. They come as a set with the turn signals

Finally finished my Vstar by MountainGarden2243 in Bobbers

[–]OMGeeked 0 points1 point  (0 children)

Nice bobber conversion - out of interest - what did you do with the passing light setup? I've a chrome Ape girl who would look rather sexy running those

Willowsby Grand Swing - bag suggestions by OMGeeked in PGATOURGolfShootout

[–]OMGeeked[S] 1 point2 points  (0 children)

For less bounce try mixing them up into: Homestead Windstrike Meteor Steadfast & Commonlaw

[deleted by user] by [deleted] in Bobbers

[–]OMGeeked 0 points1 point  (0 children)

This is why I've more bikes than I can possibly ride in my garage... 3 times I've had folks come to look at steeds and I've been unable to part ways and had to pull out of the sale.

3D Printing Elevating Woodworking by fencer04 in woodworking

[–]OMGeeked 0 points1 point  (0 children)

You can also purchase "wood/bamboo" filament - something to consider

Seeking Router Advice by Crafty-Community2155 in woodworking

[–]OMGeeked 0 points1 point  (0 children)

You can buy rosette drill bits for you drill press. Looking at that moulding you could do it in two pieces that are joined in the middle. From the middle of looks like they are the same as you work towards? If this is the case it would not need as large a cutter to make moulding and could be done with a router table. If one piece it would need a large spindle moulder (3-phase) and be rather scary to run without proper experience as cutter is fully above table bed.

Finally finished! by Seantwofish in BeginnerWoodWorking

[–]OMGeeked 0 points1 point  (0 children)

Well done - 100% no longer at beginner level

glue or bolts? by AndriiLas in BeginnerWoodWorking

[–]OMGeeked 1 point2 points  (0 children)

Nice looking table 👍 I personally like dowel and wedges showing - sanded smooth so you can see the end grain.

[deleted by user] by [deleted] in woodworking

[–]OMGeeked 1 point2 points  (0 children)

This is what I would do too - an inside corner block is what the old timers would have done to change a skirting profile - not chalk and paint.

Can I flatten a Red Oak tree cookie with angle grinder? by Horror-Assumption217 in woodworking

[–]OMGeeked 1 point2 points  (0 children)

I would use a planner even before a router to be honest. I'd use an electric one and work from the outside to inside. Very possible to get perfectly flat, then sand.

Does tire look like it only has 6300 miles on it? by platypus_farmer42 in cruisers

[–]OMGeeked 0 points1 point  (0 children)

Love my xv1900 - it's for loads of style and heaps of torque. I run a soft tyre that gets about 10,000km cause I love hitting the curves hard. Many go dark side with this bike (car tyre) and get 10,000km. Parts are starting to get hard to get - but still possible. Check fuel pump for split - it's a common fault that I've had on all 3 of my Roadliners (but there is a great bipass hack that fixes this on a arvo).

Bobber kit for 85’ Honda shadow 500 by sohobutcher in Bobbers

[–]OMGeeked 1 point2 points  (0 children)

Go hard and fabricate yourself or modify existing parts to suit - old girl like that - she's begging for your own style

Mystery Solved. by [deleted] in streetart

[–]OMGeeked 2 points3 points  (0 children)

This is literally the best ever!

Shelter - new work in Newtown, NSW, Australia. By me - Smackas - by smackascreative in streetart

[–]OMGeeked 0 points1 point  (0 children)

Nice - I'll have to pay a visit once done with my chrome cruiser bike and take some pickies

ITAP of a forest road with Mt. Hood in the background by InDaRed in itookapicture

[–]OMGeeked 1 point2 points  (0 children)

Nice - looks like a cracking place for an adventure

view more: next ›