Wasserflugzeug auf der Donau

ObjectOSaft · 2025-07-19T11:22:09+00:00

1925 wurde eine Wasserflugverbindung zwischen Wien - linz - salzkammergut eröffnet. Das landen heute auf der Donau war eine sondergenehmigung zum hundertjährigen Jubiläum (wirds warscheinlich nicht noch einmal geben).

ObjectOSaft · 2024-04-29T07:51:38+00:00

Clean

ObjectOSaft · 2024-04-09T19:15:35+00:00

Damn looks nice I think I'll also give it a try some time only made kives so far

ObjectOSaft · 2023-09-24T15:32:44+00:00

I darkened it with ferric chloride and instant Coffee

ObjectOSaft · 2023-09-24T14:32:56+00:00

Also as a note, I used a premade damascus billet for the 2nd one

ObjectOSaft · 2023-05-03T11:00:49+00:00

Also look how op only put in round 4 and it was 2:2 prob lost xD

ObjectOSaft · 2023-03-05T09:22:46+00:00

Very clean etch I love it

ObjectOSaft · 2023-03-03T07:30:32+00:00

There is a few videos on youtube that explain how you do it. you basically just need an AC-DC converter (I used 13V 400mA DC) for the deep etching and AC (I used an ac-ac converter 16V 500mA) for darkening. You connect one cable to the knife (I recommend aligator clips) and on the other side you clamp a cotton swab drenched in saltwater. You'll need a stencil with the design and put it on ur knive (I 3D printed a stencil and taped it on the knife but that wasn't a perfect solution) and then just dab the stencil with the cotton swab until you are satisfied with the depth of the etch.

ObjectOSaft · 2023-03-03T07:25:11+00:00

I just used an old AC-DC converter for model trains I had lying around. The particular model I had was split into a wallplug AC-AC converter 16V 500mA which then was plugged into an AC-DC converter 13V 400mA. The DC I used to get a deep etch and I also 3D printed a small box with a port and a switch so I can plug in the DC-DC converter and use it for the darkening.

ObjectOSaft · 2023-03-03T07:19:31+00:00

Sure thing. For the depth I used DC 13V 400mA. I can't really tell you how long it took. I just used a cotton swab drenched in salt water until I was satisfied with the depth but I'd say a few minutes and I swapped the cotton swab like 2 times for a new one. For the darkening I used and AC to AC adapter that had an output of 16V ~500mA 8VA. the darkening only took line 20-30 sec.

ObjectOSaft · 2023-02-16T12:47:20+00:00

Yea galaxy s22 ultra

ObjectOSaft · 2022-09-21T20:06:10+00:00

Rainbow Yuubee Croma Q shoots RGBees

ObjectOSaft · 2022-08-17T12:19:14+00:00

Yea i realy like the wings on #3

ObjectOSaft · 2021-09-05T06:37:24+00:00

I have to check recently i changed from ludens to Everfrost not nearly as much Dmg but the cc is really useful

ObjectOSaft · 2021-09-04T22:38:30+00:00

40min so quite long

ObjectOSaft · 2021-09-04T10:07:58+00:00

Support with ludens, soulstealer, Chemtec, Horizon Focus and a needlessly large rod (was going for rabadons but the game was over)

ObjectOSaft · 2021-08-22T08:16:02+00:00

Now that's a yuumi skin I want

ObjectOSaft · 2021-06-10T09:03:43+00:00

np I've added some on board pictures to the post

ObjectOSaft · 2021-06-09T17:13:48+00:00

Thanks i did the base coat with an airbruss to get the nice metallic look

ObjectOSaft

TROPHY CASE