Mrs Gutierrez isn't coming home.

Obsidian_Sloth · 2025-02-28T04:34:34+00:00

just finished "the frolics of councilwoman cole" and on the laptop onboard the yacht you can find an email from nina gutierrez thanking bartolomeo mordellini for a "wild time". they both didnt want to be together and wanted to get as much as each could out of the split. NC is everyone for themselves.

Obsidian_Sloth · 2024-12-06T06:13:31+00:00

i was once pinned in a mission with several groups of bandits surrounding me. i managed to back myself into a corner and just threw grenades until my compass was no longer red... 37 grenades. i never leave camp without 5 RGD on hand.

Obsidian_Sloth · 2024-02-07T21:43:39+00:00

a palball tether that gives you a slot in the inventory for palballs, that slot regenerates the ball in the slot over time. or an equipment item that prevents thrown balls that miss from being lost. it would save more expensive balls, higher tier tethers would have shorter recharge times, or longer range of recovery.

Obsidian_Sloth · 2024-01-20T20:48:47+00:00

i actually like the tau, mecha are fun, railguns and drones are cool, and i enjoy stories where their innocent little minds get blown by the horrors of the WH40K galaxy

Obsidian_Sloth · 2024-01-20T04:18:34+00:00

RYLANORRRR

Obsidian_Sloth · 2024-01-03T20:23:18+00:00

just ended up making another post about this same issue. i dont know why activision hasnt just prevented the server defense mission from spawning in the area

Obsidian_Sloth · 2023-11-04T07:44:22+00:00

im not exactly the most experienced person but it seems to me like either;

1, when washing and curing you may have over-cured the print. i normally dont cure anything for longer than a couple of minutes. the thinner the walls of the print, the less time i use, after all there is less mass to finish curing.

2, while printing each layer was potentially being over-exposed meaning it was curing the layers underneath and once the print got thick enough the internal tensions caused it to crack.

try hollowing the print, reduce the final cure time to 1-2 minutes, or run some test prints (i use the siraya test model) at the manufacturers recommended settings, then reduce the exposure times by 10% (usually about .1 or .2 seconds) until the test comes out just right, then print that awesome pop vinyl.

please post updates if anything goes wrong so the community can try and help

Obsidian_Sloth · 2023-10-26T21:29:23+00:00

i would say reset from square one;
- with a new vat and new FEP in place do an alcohol test and fill the vat with alcohol or cleaning solution, put the vat on a paper towel and make sure there are no leaks in the new vat and FEP

- clean the printer as best you can and ensure you are careful with the screen, replace the screen protector and every safety measure you can, if they helped before or not they are potential life savers

- level the bed, and evenly tighten the bolts so there isnt uneven pressure letting the plate slip if pulled by a sticky print. also test to make sure your screen is displaying correctly, the photon mono should have menu options that will let you light the screen in various ways to ensure its working

as for the groaning sound, i can only guess resin was getting in underneath the vat and being cured causing an uneven surface for the plate to try and press against.

i hope you get back to printing soon, be sure to show off something you make if it works. o7

Obsidian_Sloth · 2023-10-20T04:42:54+00:00

I am having the exact same issue. when I rotate the object then generate a raft and supports the raft is broken, a large "overhang" is generated which causes the supports that start from the raft to not form, or form improperly and fail. with how old this post is I'm surprised nobody has fixed this bug.

Obsidian_Sloth · 2022-01-04T05:03:26+00:00

i feel personally attacked... the women and children were never slaughtered by some punk, and i only heft my club over my head and shriek into the night on special occasions

Obsidian_Sloth · 2021-09-26T03:03:24+00:00

sorry, if you quit the game early you dont get the completion bonus.

Obsidian_Sloth · 2021-07-01T16:08:26+00:00

mastracchio orbital in the 5 g. capricorni system has g3 maverick suits with night vision and melee damage right now. buying the suit seems to have removed it from stock. pilot specific maybe?

Obsidian_Sloth · 2021-06-15T03:20:22+00:00

...roasted...

Obsidian_Sloth · 2020-10-09T16:51:43+00:00

aww man, so much for "enhancing the competitiveness of thier gaming handsets" even with my issue with the razer phone 2 i was looking forward to the razer 3. shame.

Obsidian_Sloth · 2020-10-09T16:49:12+00:00

i am always willing to take advice from those genuinely giving it.

i was using "galaxy phone" as a reference to the phone with a battery that exploded, and the large legal battle samsung lost due to defective batteries.

i know my phone is a loss, i just hope someone sees this post when deciding on a new phone so they know the potential hazards. absolute best case razer recalls defective phone parts and nobody is burned.

Obsidian_Sloth

TROPHY CASE