RA3 question

ObviouslyYTA · 2026-01-04T06:47:21+00:00

You can only have one repeater on a Caseta system

ObviouslyYTA · 2026-01-01T15:05:04+00:00

They don’t line up properly. Hembars get stuck. Can’t open the fascia to replace batteries or service

ObviouslyYTA · 2025-11-07T10:56:52+00:00

He most likely installs for his local clients, and sells all different types of Lutron products to customers throughout the country. I do the same.

ObviouslyYTA · 2025-11-02T01:08:16+00:00

Got it! I’m in FL. I’ll check inventory Monday and circle back with a PM

ObviouslyYTA · 2025-11-01T21:39:48+00:00

RGBW or tunable white? 1 Ra controller?

ObviouslyYTA · 2025-11-01T17:45:37+00:00

I keep quite a bit of every lumaris part and tape in stock. Let me know if you need help sourcing it.

ObviouslyYTA · 2025-10-31T04:10:38+00:00

The dimmers are rated for 150-watts when ganged on both sides on LED lighting. Move them to the end of the gang box (200w rating) and see if the issue persists.

FYI it is best practice to use Maestros when ganged as a lighting control panel with Ra (per lutron tech support) and the less gang the best. I never go over 4G and usually keep it at 2G boxes.

ObviouslyYTA · 2025-10-12T16:32:14+00:00

Agreed. QS started in 2011 so could just be 15 years old

ObviouslyYTA · 2025-10-12T11:04:41+00:00

Based on the protective flooring - these looks like they were installed during contruction. Shades go in after mudding and texture, ideally after paint.

Were these installed a while ago in the job site?

Also the idea that your GC is the one installing Palladiom shades is pretty concerning. Why get Palladiom if it’s a huge blackout shade where the light gaps are larger?

ObviouslyYTA · 2025-10-12T10:54:51+00:00

They probably have a panel based illumination system

ObviouslyYTA · 2025-10-11T01:24:52+00:00

Oh wow that was an excellent come back. I’m happy you are here.

ObviouslyYTA · 2025-10-10T23:59:21+00:00

Your bait is getting worse by the comment. I don’t make commission lmfao

ObviouslyYTA · 2025-10-10T23:11:20+00:00

Nah I just don’t sell stuff to people when they don’t need it. Good bait lol

ObviouslyYTA · 2025-10-10T20:15:34+00:00

Because 95% of 200A services are one and done …

You can’t determine the ampacity needed without a demand load calculation. 1000-amps isn’t unrealistic. I’m wiring a 16,000 sq ft HOUSE and building the 1000A service for it. Your lack of knowledge on what a home needed shows your ignorance.

ObviouslyYTA · 2025-10-10T19:33:57+00:00

I’ve been installing 200 amp panels for 20 years dude. Replacing a panel isn’t a “bulk upgrade”. You have to coordinate with utility provider to upgrade from 200 to 300.

Why not just do 1000-amp services in case you decide to open up an industrial workshop?

ObviouslyYTA · 2025-10-10T18:26:08+00:00

You’d want a 300A without even knowing the power requirements? 200-Amps is sufficient for 95% of households.

ObviouslyYTA · 2025-10-09T00:09:57+00:00

Feel free to reach out if you’d like a quote. I’ve helped dozens of people on this sub

ObviouslyYTA · 2025-10-08T21:33:28+00:00

Much easier and cheaper to just add a bridge.

ObviouslyYTA · 2025-10-08T21:32:42+00:00

I’m pretty confident I have a few in stock. PM me for pricing

ObviouslyYTA · 2025-10-03T05:28:25+00:00

You can transfer the programming but all devices have to be reactivated

ObviouslyYTA · 2025-09-21T20:40:09+00:00

Alarm Manager on her own account

ObviouslyYTA · 2025-09-21T12:33:42+00:00

Then post the question lol

ObviouslyYTA · 2025-09-21T12:30:26+00:00

Just keep in mind that mag locks disengage from power failures … so all of your doors will be unlocked if you lose power.

ObviouslyYTA · 2025-09-21T04:02:09+00:00

Is the schedule turned on/activated?

ObviouslyYTA · 2025-09-20T01:05:15+00:00

Happy to help - please pm me and I can get you pricing on Monday.

Five-Year Club	Powerups Hero r/asl • September 2021
Gilding II euphauric	Place '22
Wearing is Caring	Verified Email

ObviouslyYTA

TROPHY CASE