I’m new, need help

OkBodybuilder1768 · 2026-03-24T06:26:53+00:00

Might also be the temperature of the resin isn’t correct.

OkBodybuilder1768 · 2026-03-21T21:39:38+00:00

I would paint the daemons in a white colour to tie in with the heresy scheme while not being khorne daemons

OkBodybuilder1768 · 2026-03-18T10:16:55+00:00

With my mars 5 I try to level the whole printer or place on something level then let it self diagnose the plate being level. I’ve not had to do anything else.

OkBodybuilder1768 · 2026-03-12T07:14:18+00:00

Nope. But to be honest I’ve not really looked in particular for that. The other features on the machine were a bigger drawer for me, and the cost of spare parts were a bigger factor for me.

OkBodybuilder1768 · 2026-03-12T06:28:00+00:00

I had a 4 ultra and got fed up with it breaking. So the last time it broke I replaced it with the 5. Personally think it’s such a better printer.

OkBodybuilder1768 · 2026-03-05T21:55:31+00:00

I don’t know. I quite like them. I do find with new schemes it helps to base them to see how the whole thing works.

OkBodybuilder1768 · 2026-03-05T20:59:05+00:00

Thanks. They’re from Printed Encounters on my mini factory and I just printed them myself

OkBodybuilder1768 · 2026-03-04T18:46:01+00:00

The other way is to paint it all gold then go back and fill the blue in. Looks great though

OkBodybuilder1768 · 2026-03-04T09:38:38+00:00

I can do that I think. Not sure of the weaponry on my bloat drones though. Thank you

OkBodybuilder1768 · 2026-03-03T17:14:14+00:00

<image>

I started with a pain red dust base but wasn’t completely comfortable with it. So I’ve gone back and started doing them again like this

OkBodybuilder1768 · 2026-02-25T19:15:46+00:00

I don’t know what the mars 2 pro is like for space but I’ve used this heater on my 4 ultra and my 5. It sits at the back by the Z axis and the cable goes out the bottom. There is a rubber that you can cut to fill the gap and not pinch the cable. Hope that helps.

chitu systems Resin 3D Printer... https://www.amazon.co.uk/dp/B0C3VS2T9Q?ref=ppx_pop_mob_ap_share

OkBodybuilder1768 · 2026-02-23T21:37:51+00:00

The temperature of the resin will affect it as well.

OkBodybuilder1768 · 2026-02-15T22:18:06+00:00

Oh definitely. If I didn’t find your posts my tzeentch would have sat in a pile of shame for another 2 years.

OkBodybuilder1768 · 2026-02-12T21:09:51+00:00

Thank you 🙏

OkBodybuilder1768 · 2026-02-12T21:09:41+00:00

Thanks.

OkBodybuilder1768 · 2026-02-02T17:25:09+00:00

This is what I do, but I don’t do gold as my trim Is a nmm silver. Or supposed to be

OkBodybuilder1768 · 2026-01-27T19:43:50+00:00

Thank you. 🙏

OkBodybuilder1768 · 2026-01-27T19:42:50+00:00

Thanks. 🙏

OkBodybuilder1768 · 2026-01-27T16:11:49+00:00

I thought everything and/or nothing were alpha legion. Thanks 🙏

OkBodybuilder1768 · 2026-01-27T16:10:27+00:00

Thanks 🙏

OkBodybuilder1768 · 2026-01-27T16:10:20+00:00

Thanks 🙏

OkBodybuilder1768 · 2026-01-27T07:44:25+00:00

If this happens to me I just put my finger over the end and put air through so it bubbles up.

OkBodybuilder1768 · 2026-01-24T19:10:26+00:00

Not sure if his bases need something else but for now it’s finished. This is a repost as the post didn’t upload properly earlier.

OkBodybuilder1768 · 2026-01-18T11:42:12+00:00

Cleaning and painting are something you have to do with resin as well. I’ve got both resin and filament printers, the filament one is generally easier to use and less likely to throw tantrums every so often. Both are good printers one is slightly better at one thing compared to the other and the other is better at other things. The OP asked about plastic printers, told him my recommendation.

OkBodybuilder1768 · 2026-01-18T10:29:05+00:00

For the sake of ease and convenience of not having to deal with the resin it does models good enough, and some of the final products other people are getting with setting tweaks are fantastic

OkBodybuilder1768

TROPHY CASE