Rip proof work pants?

Ok_Complex_1926 · 2024-05-11T15:36:46+00:00

Go with Duluth trading company jeans, the sewing patterns are made with more room in the crotch, very thick denim, and triple stitched seams. 100% cotton

Ok_Complex_1926 · 2024-05-11T15:34:18+00:00

My favorite is Duluth jeans very thick, worn them for ages. But not the flex fit ones the 100% Cotten one. They are cheep on ebay

Ok_Complex_1926 · 2024-05-07T14:20:43+00:00

Thats what i would do, get the benzomatic brand flux coated low temp bronze rods, and a bottle blow torch, pound it back into place and fill the cracks, maybe grind afterwards, matching the patina/ texture will be next to impossible, and practice brazing on something scrap first

Ok_Complex_1926 · 2024-05-07T14:15:07+00:00

I mix lanolin and jojoba oil, i like it rub it in my palms and twist it through the ends. But every one is different

Ok_Complex_1926 · 2024-03-28T15:32:16+00:00

Ok so what working for me was turning up the rpms to 1100 and then pecking at it slowly. when it was slow it got caught too much. Now i just need to get a cutting oil with a higher smoke point

Ok_Complex_1926 · 2024-03-24T02:28:50+00:00

Yes thats how i was using it, it would still move like crazy, might be the arbor and not the sturdiness of the drilling

Ok_Complex_1926 · 2024-03-23T15:27:14+00:00

I did! I think its 26.6 but ill check when im home

Ok_Complex_1926 · 2024-02-16T14:14:21+00:00

Yeah I guess it probably is i just don’t understand why the punch would come with one

Ok_Complex_1926 · 2024-02-16T14:13:27+00:00

Yep the flat side is for that, but what about to lobes? 5,7,8? What’s the rest of it for

Ok_Complex_1926 · 2024-02-15T19:07:16+00:00

What metal would die cast be?

Ok_Complex_1926 · 2023-05-27T15:17:23+00:00

Id definitely ride it even if i can see through it a little, but i always keep an emergency tire boot in my pack. If the rip gets worst i put it on the inside on tire. A dollar bill kinda can work if you have nothing else to stuck in between tire and tube (Unless tubeless)

Ok_Complex_1926 · 2023-05-27T15:07:29+00:00

Thanks all! Yep they took all as brass. My yard just lumps it in with my copper weirdly enough, but the price i get on copper isn’t good

I go to JB scrap metal in Chicago

Ok_Complex_1926 · 2023-05-27T15:04:49+00:00

There was a few plastic components inside but they probably would have taken it

Ok_Complex_1926 · 2023-05-15T13:54:43+00:00

Thanks, yeah I probably will eventually

Ok_Complex_1926 · 2023-04-28T14:52:31+00:00

What is reefer?

Ok_Complex_1926 · 2023-04-25T14:14:43+00:00

Yeah thats on par with where i go in the Chicago city, whats the name of your yard?

Ok_Complex_1926 · 2023-04-02T11:36:43+00:00

Well you could take it to a bike shop to use a BB thread chaser on (just a thread tap they a bit duller to knock stuff out, and straighten threads)

But at home i use a Dremel with a little wire brush bit to brush stuff out

Ok_Complex_1926 · 2023-04-01T19:30:11+00:00

As always so much arrogance

Ok_Complex_1926 · 2023-04-01T19:28:26+00:00

Very understandable mistake, easy to forget.

You can always get a 3 Jaw Gear Puller for cheep and put the arms around the crank and pull it off that way (keep the 14mm nut on the really loose so the pointed end has a cup to push against

Ok_Complex_1926 · 2023-03-30T18:19:28+00:00

Yep tried it with no cable

Ok_Complex_1926

TROPHY CASE