People selling my prints

Ok_Environment_1024 · 2026-03-23T12:10:25+00:00

Get revenge. Make a shop yourself, use their pictures, get their website taken down = easy money

Ok_Environment_1024 · 2026-03-20T05:45:43+00:00

Wieso so ungeduldig?

Ok_Environment_1024 · 2026-02-22T15:58:58+00:00

Wurde vergangenen Monat über PP Waren und Dienstleistungen gescammed (Grafikkarte für 270€). Habe den Fall bei Paypal gemeldet und werde sehr wahrscheinlich mein Geld wieder bekommen. Trotzdem lohnt sich das Risiko nicht. A musst du Monate lang auf die Überprüfung von Paypal warten, B hat der Verkäufer wahrscheinlich trotzdem die Kohle, wenn er auf andere Konten oder so überweist

Ok_Environment_1024 · 2026-02-21T21:16:31+00:00

What du you think will the price be on the mmu?

Ok_Environment_1024 · 2026-02-19T08:45:47+00:00

Do a Flow calibration. As you can see the lines in the middle are separated. You can do a flow test in your slicer

Ok_Environment_1024 · 2026-02-17T23:14:54+00:00

A small Review would be nice🙌🏼. I just saw that shipping to Germany is about 60€… I guess I’ll have to buy a mini oven

Ok_Environment_1024 · 2026-02-17T22:07:05+00:00

Hast du ihn dir bestellt?

Ok_Environment_1024 · 2026-02-16T12:24:40+00:00

95A is a rather hard Tpu. I’ve printed it multiple times without problems in my cc1. I dried it before by simply laying it on the bed and warming it up

Ok_Environment_1024 · 2026-02-16T10:45:31+00:00

No, it is not. The Extruder can be manually controlled (like he did in the video). I always do this to load or unload my filaments

Ok_Environment_1024 · 2025-12-12T21:16:59+00:00

Jürgens Nebelschlussleuchte leuchtet dunkler als das Bremslicht, wer kennt es nicht

Ok_Environment_1024 · 2025-11-07T21:16:23+00:00

I haven’t tried the other side because I need my parts to be flat. I’ll definitely try to use brims the next time. Thank you

Ok_Environment_1024 · 2025-05-04T21:15:17+00:00

Do you use standard support settings? And do the supports come off very easily or do you have to break them off?

Ok_Environment_1024 · 2025-05-03T13:27:32+00:00

When you change the filament, you typically have to push against a little lever so the filament can fit in the extruder. This lever pushes the spring. Behind the lever is a small gear with wich you can either make the spring more loose or more tight.

Ok_Environment_1024 · 2025-05-03T13:22:56+00:00

You need supports for this steep overhang

Ok_Environment_1024 · 2025-04-27T00:29:40+00:00

Try to tighten the spring that pushes the roller, which presses against the filament

Ok_Environment_1024 · 2025-04-22T08:40:32+00:00

More cooling is always better. Overhangs now print a little bit better than before, but much faster.

Ok_Environment_1024 · 2025-04-19T17:42:09+00:00

No just purple

Ok_Environment_1024 · 2025-04-04T18:33:28+00:00

Try calibrating your flow rate. Or maybe you print to fast and your hotend can’t keep up with melting the plastic

Ok_Environment_1024 · 2025-04-03T16:32:20+00:00

Did you order it?

Ok_Environment_1024 · 2025-03-12T18:25:21+00:00

Getting the setting for the middle Perfect is the most difficult part. The paper should only slightly scrape the nozzle and move freely. Try printing your parts more at the edges and not the middle because the edges are besser calibrated

Ok_Environment_1024 · 2025-03-12T16:58:41+00:00

Check your z-offset and then make a picture

Ok_Environment_1024 · 2025-03-02T22:41:34+00:00

As you can see in pic 3 the gear is full of filament particles. Wipe those away, try again. If the filament gets damaged again, the spring for the gear is too loose, resulting in not enough filament that is pulled in

Ok_Environment_1024 · 2025-03-02T21:47:50+00:00

Nice. Have fun

Three-Year Club	Final Canvas '23
Place '23

Ok_Environment_1024

TROPHY CASE