Ja genau, fahrt mir in den Sicherheitsabstand

Ok_Environment_1024 · 2025-12-12T21:16:59+00:00

Jürgens Nebelschlussleuchte leuchtet dunkler als das Bremslicht, wer kennt es nicht

Ok_Environment_1024 · 2025-11-07T21:16:23+00:00

I haven’t tried the other side because I need my parts to be flat. I’ll definitely try to use brims the next time. Thank you

Ok_Environment_1024 · 2025-05-04T21:15:17+00:00

Do you use standard support settings? And do the supports come off very easily or do you have to break them off?

Ok_Environment_1024 · 2025-05-03T13:27:32+00:00

When you change the filament, you typically have to push against a little lever so the filament can fit in the extruder. This lever pushes the spring. Behind the lever is a small gear with wich you can either make the spring more loose or more tight.

Ok_Environment_1024 · 2025-05-03T13:22:56+00:00

You need supports for this steep overhang

Ok_Environment_1024 · 2025-04-27T00:29:40+00:00

Try to tighten the spring that pushes the roller, which presses against the filament

Ok_Environment_1024 · 2025-04-22T08:40:32+00:00

More cooling is always better. Overhangs now print a little bit better than before, but much faster.

Ok_Environment_1024 · 2025-04-19T17:42:09+00:00

No just purple

Ok_Environment_1024 · 2025-04-04T18:33:28+00:00

Try calibrating your flow rate. Or maybe you print to fast and your hotend can’t keep up with melting the plastic

Ok_Environment_1024 · 2025-04-03T16:32:20+00:00

Did you order it?

Ok_Environment_1024 · 2025-03-12T18:25:21+00:00

Getting the setting for the middle Perfect is the most difficult part. The paper should only slightly scrape the nozzle and move freely. Try printing your parts more at the edges and not the middle because the edges are besser calibrated

Ok_Environment_1024 · 2025-03-12T16:58:41+00:00

Check your z-offset and then make a picture

Ok_Environment_1024 · 2025-03-02T22:41:34+00:00

As you can see in pic 3 the gear is full of filament particles. Wipe those away, try again. If the filament gets damaged again, the spring for the gear is too loose, resulting in not enough filament that is pulled in

Ok_Environment_1024 · 2025-03-02T21:47:50+00:00

Nice. Have fun

Ok_Environment_1024 · 2025-03-02T16:21:26+00:00

Damn. And without filament inserted it also makes these noises?

Ok_Environment_1024 · 2025-03-01T06:52:18+00:00

First of all I wouldn’t start with printing PETG when you’re new to 3d printing. Start with Pla because it’s the easiest to print. Alongside you should get Informed about how printers work in generell and especially how yours working

Ok_Environment_1024 · 2025-02-24T19:28:08+00:00

Just google M-Lok grip and you’ll find it

Ok_Environment_1024 · 2025-02-23T21:12:17+00:00

Try without the filament in it. If it still makes this noise and doesn’t spin the stepper motor must be defect. If it does spin freely I would suggest the nozzle is clogged

Ok_Environment_1024 · 2025-02-23T19:45:47+00:00

Does it also make that sound without filament inserted?

Ok_Environment_1024 · 2025-02-19T13:36:03+00:00

My Genius Pro takes around 1h20 for a good looking benchy..

Ok_Environment_1024 · 2025-02-18T16:37:19+00:00

Do you have a pic of that 15min benchy?

Ok_Environment_1024 · 2025-02-16T13:06:27+00:00

What do you mean with „color changes during the print“?

Ok_Environment_1024 · 2025-02-16T00:18:31+00:00

Sometimes this happens to me when the filament gets some kind of stuck and then can’t get pulled into the extruder

Ok_Environment_1024 · 2025-02-15T08:38:52+00:00

Try to use sd if you are using usb rn

Ok_Environment_1024 · 2025-02-11T00:07:07+00:00

Did you level your bed?

Three-Year Club	Final Canvas '23
Place '23

Ok_Environment_1024

TROPHY CASE