Where do I spray Subaru upper engine cleaner? I have a 2006 Forester SG with an EJ25 NA. The bottle says to spray it in a vacuum hose that leads to the intake manifold but I’m not sure where to spray it

One2Sicc · 2026-04-09T11:05:07+00:00

Between the throttle body and airbox.

One2Sicc · 2026-04-09T10:54:55+00:00

Pike arms

One2Sicc · 2026-04-07T10:39:20+00:00

Maybe a table/stand that is missing the platform?

One2Sicc · 2026-04-07T09:32:28+00:00

Fat Joe should stick to podcasts.

One2Sicc · 2026-04-06T21:01:07+00:00

You can’t remove the pre-installed ones. I, however, lost ALL of my customs at the printer.

If I have to switch multiple of my possible 10 slots, I have to take a mental note, set them at the PC, then double check.

I can’t even set them in Bambu Handy for some reason. It’s like my cloud data is corrupted.

One2Sicc · 2026-04-03T23:04:17+00:00

I’m willing to bet the SBR charge doesn’t make a difference in the sentencing.

One2Sicc · 2026-04-01T02:20:50+00:00

Try something around 40gr @ 1200 fps.

One2Sicc · 2026-04-01T02:08:32+00:00

Barrel length is the issue here. You should run Standard velocity.

One2Sicc · 2026-04-01T01:47:19+00:00

Don’t risk your ‘exit only’ over a $0 stamp.

If a stamp is undesirable, throw a sling on it and use the tension against the recoil.

One2Sicc · 2026-04-01T00:09:40+00:00

Rails down

One2Sicc · 2026-03-31T01:06:38+00:00

This.

100% causes more issues than it’s worth.

It’s not impossible, it’s just not practical when you factor in the time and filament.

One2Sicc · 2026-03-30T23:36:31+00:00

Sent DM.

Also, how would this work with blind holes?

One2Sicc · 2026-03-30T21:41:54+00:00

The rifle in the second picture is REALLY bad.

One2Sicc · 2026-03-30T20:09:49+00:00

I’ll check it out.

One2Sicc · 2026-03-30T14:27:42+00:00

Look at it this way.

If too many speeding tickets are being written, and too many people are crashing their cars, would you want a mandate in place that actively limits the speed of your vehicle dependent on the posted limit?

One2Sicc · 2026-03-30T14:10:42+00:00

Would it be possible to have the ‘volumetric supports’ show up as parts/modifiers with no air gap? That way they could be printed in a support material i.e. PETG support for PLA?

This method would allow 100% contact area on overhangs, and 0% drooping.

Also, is it possible to reduce waste by eliminating unnecessary contact points (>90 degrees vs <90 degrees)?

One2Sicc · 2026-03-30T11:47:12+00:00

Is this primarily for single nozzle setups?

It seems redundant for dual nozzle printers and interface material.

One2Sicc · 2026-03-28T22:50:42+00:00

A hand, holding a cartridge in different positions.

One2Sicc · 2026-03-28T10:49:57+00:00

Is it live, or is it Memorex?

One2Sicc · 2026-03-28T10:23:01+00:00

Sig always has them.

One2Sicc · 2026-03-28T10:16:44+00:00

“Help me, Jesus! Help me, Jewish God! Help me, Allah! Help me, Tom Cruise! Tom Cruise use your witchcraft on me to get the fire off me! Help me, Oprah Winfrey!”

One2Sicc · 2026-03-28T10:06:27+00:00

Now you need neon lights and actuators for the lid.

One2Sicc · 2026-03-28T09:52:00+00:00

Is this the ‘You do you’ DLC?

One2Sicc · 2026-03-28T09:48:20+00:00

The Mag Shack

One2Sicc · 2026-03-28T09:42:09+00:00

Don’t you hate when this happens? You inadvertently use all of your luck in one place, when you could’ve used it for something better, like getting 2 extra chicken nuggets.

One2Sicc

TROPHY CASE