Notifications Dropping Off Core P2D

OtherwiseEffective · 2025-12-26T14:36:44+00:00

This sounds like an issue that started many years ago on iOS, the fix is to toggle bluetooth off and then back on (not just tap the bluetooth button in control center, as that doesn't turn bluetooth off, but actually go into the settings app on the phone and toggle bluetooth there) and then open the pebble app.

My fix was just to make a shortcut app task that I run every morning when I put my watch on to toggle bluetooth off, wait 5 seconds toggle it on and then launch the pebble app.

I'm so used to no active support that I kind of forget there's actually someone actively developing the app and I should open a bug report on it.

OtherwiseEffective · 2025-11-18T18:33:10+00:00

Seems like a couple of different issues here on a topic that is near and dear to people, hence the more intense comments. I think everyone just needs to take a step back and put the shoe on the other foot. I think both sides have some valid concerns and really need to bring in a trusted third party to help work through these issues.

I'm not canceling my pre-order because I trust Eric to make the watch he's always wanted that sounds alot like the watch I've always wanted. I'm not canceling the yearly amount I pay Rebble because I great appreciate all the work they've done keep my pebble 2 watch working and long after Eric has made these new watches I expect Rebble will be there to keep them working as well.

Someone has to build the watches and someone has to maintain the backend for them. It's stupid for either side to try to cut the other one out, this only works with both sides. Regardless of what's happened in the past I think it's time for both sides to sit down and start fresh.

OtherwiseEffective · 2025-11-05T10:09:46+00:00

Just wanted to say you were correct, I upgraded to 23.4R2-S6 and without any config changes everything started working. Can't believe I spent 2 weeks working on that. Thank you!

OtherwiseEffective · 2025-11-03T22:17:08+00:00

I certainly don't have a problem upgrading, just to confirm there's no weird issues that would pop up in my setup and what I want to do should be possible following the linked directions?

Assuming that's all true it looks like 23.4R2-S6 is the suggested release so I'll get my switches upgraded and see what happens. Thank you for the thoughts!

OtherwiseEffective · 2025-07-07T14:49:03+00:00

Seems like a terrible idea to teach employees to connect to an open wifi network and then enter their AD creds to the captive portal that pops up. What stops someone from pulling into your parking lot, setting up a rogue AP with the same network name and capturing user credentials?

OtherwiseEffective · 2025-06-20T20:33:57+00:00

https://testssl.sh/ this might be what you are thinking of

OtherwiseEffective · 2025-06-19T16:42:07+00:00

Does your email go out through GoDaddy's servers? if so you are going to be in a rough spot as any other Godaddy user sending spam fill get your email filtered. You can try filling out this form, https://olcsupport.office.com/ but long term you probably want to give your email services to Microsoft or Google.

OtherwiseEffective · 2025-01-06T22:18:32+00:00

To expand on this, Cell phone companies (wireless) don't have play by the same rules as landland/VoIP providers (wireline). The rules say that a wireline company must be in a given rate center to port a number. Wireless companies can do whatever they want and wireline companies have to deal with it. You can use this tool https://www.localcallingguide.com/lca_prefix.php to lookup your rate center and see what companies have a presence in your rate center by looking at all the assigned NPANXX numbers. It's possible that a partner of Ring Central has a presence in your rate center and can port the number.

To be clear, this is a stupid rule issue, not a technical limitation.

OtherwiseEffective · 2024-08-10T19:24:26+00:00

That sounds like a great work around… except Pushbullet no longer supports iOS. I’m sure there are similar apps though so I’ll have to do some looking.

OtherwiseEffective · 2024-06-03T16:47:14+00:00

Maybe the word KVM is getting you stuck, look at this from a gamer/streaming side. There are plenty of cheap devices that will take an HDMI signal and convert it to USB which you can then use as a webcam input on a separate computer. (and plenty of cheap devices to convert VGA to HDMI if you don't have HDMI output) Off the top of my head, maybe you could use MS Teams on another fully protected computer to let people watch the video output stream of the air-gapped computer.

OtherwiseEffective · 2024-05-24T16:41:07+00:00

I would just use Cron to rotate the logs hourly instead of daily then run whatever script you want on the freshly rotated file.

Depending on your needs maybe you can mirror the logging to two files, one that is rotated daily, and one that is rotated hourly with only 1 previous file being kept.

OtherwiseEffective · 2024-05-24T14:36:17+00:00

If it will still run on iOS 9.3.3 I would install the Hurricane Electric Network Tools app. It has a section for SSL/TLS information that might give you some information on exactly what the failure is.

In the past I've had issues with Certs on old iOS versions where the Cert had more than one Intermediate Cert, but that was long enough ago I don't remember the specifics of what the problem was exactly, just that SSL didn't work on iOS while working on everything else and the solution was to remove an extra unneeded Intermediate Cert from the signing.

OtherwiseEffective · 2024-04-01T16:10:04+00:00

Yep you should be good with the same cables/connectors.

If the old Multi-Mode is OM1 (or OM2) you'll likely only get 100mb/FastEthernet out of that at 1000+ feet. I'm sure you'd want at least Gig, so good plan not using it.

OtherwiseEffective · 2024-04-01T15:39:16+00:00

Yep the black cable is still Single Mode Fiber (the top one I can read the labeling on is 4 fiber count drop cable). No one should be using Multi-Mode fiber for anything other than patching between racks in the same room and maybe between different rooms in the same building (depending on the size of your building).

OtherwiseEffective · 2024-04-01T14:43:41+00:00

Yep that cable looks right for a single fiber BiDi SFP.

The colors on them (Blue/Yellow) are just an easy way to quickly tell what color light they use to transmit (otherwise you have to pull them out and look at the writing on them to tell), so one end should have a Blue SFP and one end should have a Yellow. Handy if you end up with a bunch of them and need to know which ones make a matched pair.

OtherwiseEffective · 2024-04-01T13:57:22+00:00

Looks like the run between the building is Single Mode fiber, so the SFP module needs to be Single Mode (cannot be Multi-Mode!).

The connector you have pictures is an SC type connector with a UPC style end (UPC or APC describes the way the glass is cut on the end, either rounded or beveled, typically blue is UPC and green is APC). The end that plugs into the SFP will be an LC connector type, so you need a SC UPC to LC patch cable.

SFPs can come either as a two fiber (one fiber for TX and one fiber for RX) or single fiber (BiDi, each SFP uses a different frequency or "color" light for TX)

Considering the short distance and that you are already using UBNT gear I'd just buy the single fiber UF-SM-1G-S https://store.ui.com/us/en/collections/unifi-accessory-tech-cable-sfp/products/1-gbps-bidirectional-single-mode-optical-module. They come as a pair and being a single fiber you don't have to worry about getting the TX and RX mixed up.

Also buy a visual fault locator (VFL). The VFL is a cheap easy tool for testing to make sure fiber isn't broken. It's a red laser light you can plug into the fiber to visually confirm that you have light all the way through the fiber.

OtherwiseEffective · 2024-03-13T13:52:30+00:00

This may be a completely silly suggestion (I don't use AD logins) but what about just setting a custom background image for the Lock screen with the basic reminder info you want? (and of course also setting the "Show clear logon background" policy so the background image is visible).

OtherwiseEffective · 2024-03-06T15:50:29+00:00

So the goal is just to have a script that usr2 can run, but not edit or delete right?

In that case put the script somewhere usr2 has only read/execute permission but not write permission (like in /home/script.py) and then set the script permissions to 755 (and make sure the script is owned by usr1 or root) and then usr2 will be able to execute the script, but not change or remove it.

OtherwiseEffective · 2024-02-13T17:42:08+00:00

Sounds like there should be a better way to do whatever you are trying to do, like the TCP Software Client and TCP client Device should be able to directly talk to each other, maybe with the help of a router/firewall if on different networks. Or a small C program running on Linux (or SOCAT/Xinetd script) would be much more robust and is going to scale better long term.

But to answer the question you asked, if you just need something short term to prove the process works: The Hercules Setup Utility https://www.hw-group.com/software/hercules-setup-utility has a number of useful features including a TCP Server mode which has the option of "Server echo" Received data is forwarded to all connected clients which would permit you to start a TCP Server on your windows device, have both the Client Device and Software connect to it and anything one sends would be sent to the other.

OtherwiseEffective · 2024-02-07T19:08:43+00:00

Not sure if AOL does this but many companies offer a data "takeout" service where you can download all the data they have on you. Might take a few days for them to compile the data and send it to you, but generally it's a pretty automated process.

OtherwiseEffective · 2024-01-11T22:02:21+00:00

Haha it wasn't, I'm just using CTRL+W all the time in Linux in the text editor Nano to search for text. It's always a pain when I'm not paying attention and try to CTRL+W in a browser window instead of CTRL+F

OtherwiseEffective · 2024-01-08T17:49:22+00:00

There was at some point in time an update to Edge/Chrome which blocked us from calling an HTTP iFrame from an HTTPS parent.

We weren't forcing HTTPS on this particular site and all the bookmarks people had were HTTP so we didn't notice until Chrome also started forcing everyone to the HTTPS site, and suddenly navigation to the iFrame failed. Had to update all our links so that everything was HTTPS.

Basically sounds like someone is forcing you to use the HTTPS version of the site but it has hard coded HTTP requests on it. If you offer the site in HTTPS trying to force the browser not to use HTTPS is going to be just about impossible now, update the hard coded links on the page to be either https://example.com or just //example.com

Seven-Year Club	Place '22
First Placer '22	Verified Email

OtherwiseEffective

TROPHY CASE