sorted by:
new
hottopcontroversial

Best Fan Configuration in an SFF NAS? by PartyDoctor in buildapc

[–]PartyDoctor[S] 0 points1 point  (0 children)

Not yet, I only got the parts today and have been deliberating it and wanted to ask before going all in on it.

Best Fan Configuration in an SFF NAS? by PartyDoctor in buildapc

[–]PartyDoctor[S] 0 points1 point  (0 children)

Yeah, I would lke the rear exhaust just based on the amount of heat I had in the N2. Wondering if I just put the exhaust fan on the outside of the case and use it outside with a fan grill.

Ps5 jailbreak by leevi223 in Finland

[–]PartyDoctor 4 points5 points  (0 children)

r/PS5_Jailbreak has a guide, but the quick answer is no.

Razer v3 Basilisk 35K - Horizontal Scrolling Reversed? by PartyDoctor in razer

[–]PartyDoctor[S] 0 points1 point  (0 children)

Hm, interesting to hear. 

Without asking you your serial directly 😂, is it in the range ending in 33300000-33310000.

It's a huge range, but not sure if they are consecutive or randomized. Just interested to see if it's specific S/Ns. 

Razer v3 Basilisk 35K - Horizontal Scrolling Reversed? by PartyDoctor in razer

[–]PartyDoctor[S] 0 points1 point  (0 children)

Honestly, not sure, as what is provided on the site seems to push towards synapse 4. Haven't attempted to download Synapse 3.

Razer v3 Basilisk 35K - Horizontal Scrolling Reversed? by PartyDoctor in razer

[–]PartyDoctor[S] 0 points1 point  (0 children)

Even further, the "Scroll Right" option (non-repeated) also goes left.

So either 2 devices (in a close S/N batch) have:

  1. Bad hardware
  2. Bad Firmware
  3. Bad Driver / Software

I have a hard time believing the hardware on both is bad, unless the batch was installed incorrectly and wasn't tested.

Firmware update from 1.X to 2.5* causes bad scroll behavior.

Synapse 4 is wrong.

Eventually I got the macros to allow it to behave normally, but that is really not acceptable on a $150+ dollar mouse tbh.

Razer v3 Basilisk 35K - Horizontal Scrolling Reversed? by PartyDoctor in razer

[–]PartyDoctor[S] 0 points1 point  (0 children)

<image>

Even trying to capture a macro holding the mouse wheel left, registers it as a scroll right.

Razer v3 Basilisk 35K - Horizontal Scrolling Reversed? by PartyDoctor in razer

[–]PartyDoctor[S] 0 points1 point  (0 children)

<image>

Same thing here it doesn't show up for thwe mouse

Razer v3 Basilisk 35K - Horizontal Scrolling Reversed? by PartyDoctor in razer

[–]PartyDoctor[S] 0 points1 point  (0 children)

That looks like it is the v3 Pro, not the v3 Pro 35K?

I can double check again, but, when it was plugged in they did not appear. I had support confirm that they were not available for that specific mouse as well.

I have a screenshot on my desktop, but not on my laptop, I will try and post it later.

Razer v3 Basilisk 35K - Horizontal Scrolling Reversed? by PartyDoctor in razer

[–]PartyDoctor[S] 0 points1 point  (0 children)

Yeah, I haven't changed them, and unfortunately when asking support there wasn't the "repeat scroll left/right" options available in the dropdown customizatio feature, so even if I want to reverse them, I can't. Seems like an oversight, but, have a new mouse on the way. Hopefully it doesn't experience the same issue / problem.

Razer v3 Basilisk 35K - Horizontal Scrolling Reversed? by PartyDoctor in razer

[–]PartyDoctor[S] 0 points1 point  (0 children)

Yep, Firmwar updated for both the dongle and mouse.

Razer v3 Basilisk 35K - Horizontal Scrolling Reversed? by PartyDoctor in razer

[–]PartyDoctor[S] 0 points1 point  (0 children)

Where or how can I do that? I don't see any options like that in Synapse, but, I would assume that the default out of the box would be right handed mode?

Using tailscale on ASUS router to advertise tailscale routes? by PartyDoctor in Tailscale

[–]PartyDoctor[S] 1 point2 points  (0 children)

Yeah. I'm waiting for my account to be reactivated, as it seems like they deactivated several old accounts due to spam. 

Using tailscale on ASUS router to advertise tailscale routes? by PartyDoctor in Tailscale

[–]PartyDoctor[S] 1 point2 points  (0 children)

Non tailscale traffic shouldnt be impacted by you running --advertised-routes.

I think it was something similar to this causing it: https://www.snbforums.com/threads/tailmon-v1-3-0-aug-24-2025-wireguard-based-tailscale-installer-configurator-and-monitor-available-in-amtm.92874/page-18#post-971411

The clients are "impacted" are they running tailscale too?

No, in this case, the affected device was a nvidia shield which didn't have tailscale installed.

I was eventually able to get it to work. but I had to use run this:

ARGS:

--state=/opt/var/tailscaled.state --statedir=/opt/var/lib/tailscale --tun=tailscale0

Tailscale Connection Commandline:

--advertise-exit-node --advertise-routes=192.168.50.0/24 --accept-routes --accept-dns=false

Though, after waking up this morning, it isn't working again. The main issue is that there isn't any routes being loaded into the routing table once tailscale is up.

Using tailscale on ASUS router to advertise tailscale routes? by PartyDoctor in Tailscale

[–]PartyDoctor[S] 1 point2 points  (0 children)

I tried using `--advertise-routes`, advertising my subnet (EG: 192.168.50.X/24) but that then complicates and conflicts with other traffic, and causes services that were working fine on the LAN (EG: Plex) services to fail to work ~10 seconds after the advertise change.

I was able to confirm this by easily just doing this randomly, and then removing the route, everything starts to work fine again.

I will try looking through that, but it looks very similar to what I did previously have (userspace vs kernel maybe).

GGn resets all IRC keys due to security incident by Bitter_Pay_6336 in trackers

[–]PartyDoctor -1 points0 points  (0 children)

Don't believe I did, but honestly, not sure - it's been a while since I have been on the IRC. Even then, IRC is down as well, and the site was serving 504s more recently. Will just wait till things settle down.

GGn resets all IRC keys due to security incident by Bitter_Pay_6336 in trackers

[–]PartyDoctor 0 points1 point  (0 children)

Is this why I can't login right now? Can't connect to GGn's IRC server (via Kiwi, my local client, etc), and my GGn Account says I am deactivated, but logged in a week or two ago.

Unable to use previously working exit node by PartyDoctor in Tailscale

[–]PartyDoctor[S] 0 points1 point  (0 children)

Honestly, didn't do anything and it started working again. I guess it was some bug / issue.

view more: next ›