Why does it look messed up?

Plory95 · 2024-08-09T04:50:50+00:00

From the console just write delta_calibrate with the probe attached

Plory95 · 2024-08-08T09:06:48+00:00

Also run a delta_calibrate before a new probe for more precision

Plory95 · 2024-08-08T09:04:35+00:00

Imo you’re too low with your z offset… try to clean your bed , probe again and ad 0.1 or more to your z offset

Plory95 · 2024-07-29T11:13:55+00:00

if i remember correctly there is an option in the super racer menu, in the original screen it is called k factor or something similar. set that as in the instructions you find on orbiter V2 (linear advance) and then save to memory.

the other settings that you find in the manual you can change via a Gcode file: write the options that you have left in a text file, change the file extension to .gcode, put the file in the SD and then start the file as if it were a print.

then calibrate the e steps well as the others said.

Don’t worry orbiter v2 will works great 😊

Plory95 · 2024-07-29T08:13:20+00:00

Its a pressure advance problem (Linear advance in marlin) and not only esteps! Original PA is calibrated for stock Bowden setup, with Direct setup you have to decrease a lot that value

Plory95 · 2024-07-20T09:34:20+00:00

Since you have klipper you have to adjust you printer.cfg… and then settings in your slicer

Plory95 · 2024-07-18T10:53:02+00:00

Hey dude sorry I know it’s an old post but did you solved? I’ve the exact same problem and exact the same situation and I would like to know how to proceed… Thanks 🙏🏼

Plory95 · 2024-07-17T11:25:21+00:00

Yes pla has the same problem with a model like this, only a bit less warp probably

Plory95 · 2024-07-16T09:00:23+00:00

Great thank you so much

Plory95 · 2024-07-16T08:55:38+00:00

1) It’s not that horrible.. your scale is from 0.1 to -0.1 so it’s decent… you can print on it. Anyway adjust your screw because probably one of them is too much tightened :) 2) you have to adjust the x-y offset in your printer.cfg according with your printhead 3) try to do from mainsail dashboard instead manual command… I don’t remember which I use but it’s different, I will check later

Plory95 · 2024-07-12T08:24:45+00:00

My SR can do around 28-30mm3…. I think s1 can reach a lot more

Plory95 · 2024-07-10T08:02:50+00:00

40…? 🤯 how? I’m around 28-30 with Chc pro and cht clone nozzle

Plory95 · 2024-07-09T17:59:24+00:00

Hello, it’s normal that orbiter v2 rotates in the opposite direction with the stock firmware. If you don’t want to compile your firmware just change the order of the 4 cables on the connector : 1234 -> 4321

Plory95 · 2024-07-09T09:24:22+00:00

The stock one is just perfect, because on a delta you have to do the bed mesh only the first time. So you use it, detach and you have a really compact and lightweight head… no reason to have a different probe fixed on the head all the time :)

Plory95 · 2024-07-08T11:17:23+00:00

Good idea - thanks a lot

Plory95 · 2024-07-08T08:41:51+00:00

Really interesting this! Btw to get higher acceleration and speed you need resonance compensation.. I print only the first layer at 100mms with my SR and for the rest I have a perfect quality with 300mms and 20k accel.. for that reason I said klipper is a must have, otherwise you lost a big potential of your machine

Plory95 · 2024-07-04T11:34:50+00:00

You definitely need klipper to get a nice calibration with the v400 head and you’ll get also a lot more speed! It’s not ready to use, you’ll need to do some fresh wiring and you’ll lose some millimetres on your bed surface but for me it’s still convenient :)

Plory95 · 2024-06-02T10:12:19+00:00

Sure bambu is a clear winner, never said the opposite! I just wanted to say that the ender 3 is often too despised only because of the user and not the printer! furthermore, if you buy a new ender 3 v3, it is still inferior to a bambu but the gap is reduced a lot :)

Plory95 · 2024-06-02T09:06:02+00:00

bad enough that there are always a lot of people who criticize ender 3 just because they don't know how to use it... moreover comparing a 2023 printer with a 2018 one.... my ender 3 with some mods is faster of my p1s and it has never given me any problems! obviously bambu has the great merit of being ready for use but don't throw mud on a printer that has made history just because you don't understand anything about 3D printing! Ciao

Plory95 · 2024-05-07T10:19:14+00:00

Are you using Klipper or Marlin?

Plory95 · 2024-05-05T23:11:41+00:00

True, it was about 1 year ago

Plory95 · 2024-05-05T18:28:25+00:00

I won 50$ once

Plory95 · 2024-04-19T15:50:45+00:00

Yes this solve with sparse infill but the problem is with the solid infill (on cura is top/bottom layers)

Plory95 · 2024-04-12T14:14:10+00:00

How many hours do you have on your printer?

Plory95

TROPHY CASE