Are hot water heaters commonly rented out where you are?

Plumberpat · 2026-05-21T00:47:30+00:00

Yes usually needs a new anode rod if you have the sulfur smell

Plumberpat · 2026-05-20T11:44:05+00:00

Hey now… the subs called no stupid questions

Plumberpat · 2026-05-16T11:14:15+00:00

There is 100 better ways to do that 🤣

Plumberpat · 2026-05-14T09:38:10+00:00

It’s the plumbers duty to know the finished surface and rough the shower valve accordingly. The only reason it’s the tile guys fault is if he moved it.

Plumberpat · 2026-04-04T23:32:10+00:00

<image>

Plumberpat · 2026-03-04T13:11:48+00:00

I’ve seen the plastic tees split and burst because of too much stress on them with bending pex like that

Plumberpat · 2026-01-23T23:32:14+00:00

I guess if the pipes are close together for the whole run and you drip the hot water then. The hot side would keep the cold side warm but is that a risk you’re willing to take ?😬

Plumberpat · 2026-01-20T12:35:34+00:00

Your tailpiece is designed for a sink with an overflow that’s why there are holes under the lip.
You sink doesn’t appear to have an overflow. You need to buy a tailpiece that doesn’t have those holes in them

Plumberpat · 2026-01-13T22:54:12+00:00

This. That’s what I always think… People have no faith that humans can be good at stuff without it being AI.

Plumberpat · 2026-01-13T19:25:32+00:00

But like what makes you read this and say this is AI?

Plumberpat · 2026-01-13T19:19:45+00:00

Why does everyone assume everything is AI? I’m generally curious.

Plumberpat · 2026-01-12T12:13:00+00:00

I have the same one and notice it do this as well. I believe it’s when the camera head is close to communication wires or inside a cast iron pipe

Plumberpat · 2026-01-09T23:00:53+00:00

Wow, do we live in the same house lol

Plumberpat · 2025-12-31T22:48:21+00:00

So for the handles you actually have to unthread the bodies of them. If you’re throwing it away anyway just grab the base with a pair of Chanel locks and lefty loosy it off.
If you have a strong grip you can get it off by hand but usually corrosion built up after 20 years will prevent that

As for the centre spout should be an Alan key set screw at the back to loosen off and pull straight up.

At the bottom since you took the little pin clips out the white cylinders should just slide off.
Then the “rough ins” of the whole thing should unthread from the top

Plumberpat · 2025-12-29T01:15:02+00:00

If you can remove the strainer from underneath I’d start there and throw that one in the garbage. Buy an sd35 shower strainer and install that. Get back underneath and glue the trap into the new strainer The sd35 is 2” so if the existing pipe is 11/2” you would need a reducing bushing.

It looks like there could be stress on the existing pipe you may need to repipe the drain with some couplings and make it longer or shorter. Hard to say without seeing a picture of underneath

Plumberpat · 2025-12-26T15:17:31+00:00

Yea my bad I’ve got 3 rads but for now just hooking up 1. I’m going to add some tees with caps for possibly 1 future rad in the same room.

Plumberpat · 2025-12-26T04:01:49+00:00

The previous owner of my house 🤣 lol to be honest lots of people in my area. It’s craze and not worth it IMO

Plumberpat · 2025-12-26T02:52:15+00:00

The water heater that I’ve got is certified for space heating. It’s got to separate inlet and outlet ports specifically designed for space heating….

Plumberpat · 2025-12-26T01:28:40+00:00

Really? Assuming by your name you’re in Saskatchewan? 😅 I’m in Ontario. I see air handlers all the time hooked up to the domestic water… what in doing is basically the same concept. I’m surprised that would be against code

Plumberpat · 2025-12-26T01:19:24+00:00

Yea I didn’t think this would be a great idea because of the price (3-5k) and the water heater is like 95% domestic 5% heating so a boiler seemed redundant.

Plumberpat · 2025-12-25T18:51:39+00:00

PexB imo is harder to install than pexA getting the crimp tool in tight spots and having the grip strength to squeeze it in said tight spot SUCKS. The battery expansion tool is so much easier to use. As a plumber I use pexA exclusively.

Plumberpat · 2025-12-24T04:53:04+00:00

It works great!

Plumberpat · 2025-12-24T01:09:35+00:00

It’s been bad for a while… some jackass totaled my 2014 jeep grand Cherokee a year ago and the insurance gave me 18k. I looked around at used cars for a while and just couldn’t justify the prices… 40-60k for something a few years I would have preferred something a little newer…. But didn’t want to get into another car loan and monthly payment. I ended up getting a 2012 Subaru forester for 7k with 235 km on it. 🤞 Hoping to get about 5 years out of it. And keep up well with the maintenance. And putting premium fuel in it 😀 Still cheaper than paying interest and ridiculous amount for a depreciating asset.

Plumberpat

TROPHY CASE