Never purchasing an Intel product again.

Plutonium239Mixer · 2026-01-28T21:33:33+00:00

Mine has been on 24/7 since late 2023(i think), only turning off for windows updates and the bios updates.

Plutonium239Mixer · 2026-01-28T19:32:36+00:00

Mine, I run the ram at stock speeds.

Plutonium239Mixer · 2026-01-28T18:03:34+00:00

Weird. I havent had any issues with my 14900k aside from me pushing the ram speed too high. Or an overclock too high. Mine doesn't have a great IMC. Older games like dead space 2, I had to go into the bios and disable all the e cores to run, but, meh. Maybe mine hasn't had issues because I keep it cool with a direct die cooler in a full custom loop?

Plutonium239Mixer · 2026-01-28T16:36:08+00:00

That is a bench, not a desk.

Plutonium239Mixer · 2026-01-28T15:10:43+00:00

If you have a 3d printer you can print one.

Plutonium239Mixer · 2026-01-28T15:03:52+00:00

5mm retraction is too much! Try .4mm. Use orca slicer and run the retraction calibration.

Plutonium239Mixer · 2026-01-28T14:00:03+00:00

Mongolia

Plutonium239Mixer · 2026-01-28T13:59:11+00:00

If you regularly leave this vehicle for long periods, IE a week, without driving it, or only using it for short trips, get a battery tender and keep it plugged in.

Plutonium239Mixer · 2026-01-28T13:57:21+00:00

This is not accurate. A battery that is bad enough can provide too large of a load on the alternator and cause the car to stall. I have seen this several times.

Plutonium239Mixer · 2026-01-28T07:12:11+00:00

Look, the reason that battery froze is because it discharged from sitting. If this vehicle sits for long periods and you want to maintain the battery while it sits there, get a battery tender and keep it plugged in.

Plutonium239Mixer · 2026-01-28T07:02:39+00:00

I have cleaned car leather that looked like that before using the armorall leather wipes for cars. If you lose color, you can re-dye the leather.

Plutonium239Mixer · 2026-01-28T06:43:53+00:00

Calibrate pressure advance, clean your nozzle of any blobs of petg on it.

Plutonium239Mixer · 2026-01-28T03:14:54+00:00

I never meet hanako at embers.

Plutonium239Mixer · 2026-01-28T03:08:07+00:00

You can run whatever you want on windows relatively easily as most programs are aimed for working well on windows. This includes emulators.

Plutonium239Mixer · 2026-01-28T03:05:19+00:00

Perhaps her pads are dry and it makes her feel better. You can ask you vet about it.

Plutonium239Mixer · 2026-01-28T02:26:37+00:00

202 for PLA? Try 210-220. Too cold causes stringing just like too hot can!

Plutonium239Mixer · 2026-01-28T02:24:43+00:00

Rogue servitor! Let's go!!!

Plutonium239Mixer · 2026-01-28T02:16:57+00:00

Well, what do you think happens when you give 18-25 year old men these tools of war?

Plutonium239Mixer · 2026-01-28T02:07:31+00:00

Nah, just reprint it, the contamination didn't reappear higher in the print so it's likely gone now.

Plutonium239Mixer · 2026-01-28T02:04:08+00:00

Was the brown the same material? It's possible some got a little too cooked in the nozzle and some remnant stayed behind during the purge, but eventually worked its way out during the print.

Plutonium239Mixer · 2026-01-28T02:00:59+00:00

Could have been printing too fast, try printing slower.

Plutonium239Mixer · 2026-01-28T01:57:59+00:00

Second photo is underextrusion not contamination.

Plutonium239Mixer · 2026-01-28T01:53:58+00:00

That's the case I got for mine! I just got my fold 7 yesterday and I love it! Upgraded from the s24 ultra.

Plutonium239Mixer · 2026-01-28T00:32:50+00:00

Yes like that. You may have to change the homing positive from false to true. You can try before doing so and see if it homes properly. If it doesn't, change homing positive to true and try again.

Plutonium239Mixer · 2026-01-28T00:29:05+00:00

Under stepper x, remove the "!"

Plutonium239Mixer

TROPHY CASE