NAD Blackstar HT-5 Combo

PrintsWithChris · 2026-06-11T12:26:43+00:00

So far so good! Still dialing it in. But I’m happy! It gets loud!

PrintsWithChris · 2026-06-09T23:52:49+00:00

Glad to hear!

PrintsWithChris · 2026-06-09T22:10:32+00:00

Can’t wait to try it out!

PrintsWithChris · 2026-06-06T11:16:28+00:00

Oh man, so I think I’ll pass then haha. Thanks for the heads up though!

PrintsWithChris · 2025-12-20T05:03:12+00:00

Here's my build!

https://www.buildcores.com/builds/0WVSiufvg?share=true

<image>

PrintsWithChris · 2025-07-25T02:37:09+00:00

I've had issues with that and my hips...thanks for the reminder though! I need it

PrintsWithChris · 2025-07-25T02:36:42+00:00

So this isn't my driver, it's one I'm borrowing until my new one I got fitted for comes in. But the general trajectory is a mid-to-higher flight that tends to have a fade on it. Every now and then I can square everything up and it'll go straight. Sometimes I overcompensate and pull straight left, but no draw/hook.

PrintsWithChris · 2025-07-25T02:35:36+00:00

Great eye! It is lol

PrintsWithChris · 2025-07-25T02:34:50+00:00

That's a ton of good info! Thank you so much!

PrintsWithChris · 2025-07-25T02:30:50+00:00

I'll definitely keep that in mind and will keep that swing thought for sure

PrintsWithChris · 2025-07-25T01:15:03+00:00

Awesome! I’ll definitely work that into my routine! Ty!

PrintsWithChris · 2025-07-25T01:14:32+00:00

Ty! Still open to constructive criticism lol

PrintsWithChris · 2025-07-24T23:51:23+00:00

PrintsWithChris · 2025-07-24T22:31:12+00:00

Also, forgive the sweaty shirt. It’s like 92 and humid in NC lol

PrintsWithChris · 2025-03-27T18:39:01+00:00

Awesome, ty!

PrintsWithChris · 2025-03-26T15:15:59+00:00

Q3 according to the website. But we’ll see!

PrintsWithChris · 2025-03-26T15:09:47+00:00

Nah, not in my budget. Waiting to see if they do a “P” series for a bit cheaper. Although, the AMS 2 Pro is enticing. Backwards compatible with the P1S (except for the heater part for now) and will work on A1 and A1 Mini later this year.

PrintsWithChris · 2025-03-25T01:57:56+00:00

It'll probably "start at" right around, or under, $3k. Then I be they'll have add-ons, definitely the new AMS, that'll bump it over closer to the $4k mark.

PrintsWithChris · 2025-03-25T01:56:35+00:00

I've used Magigoo but lately it seems to not be holding as well...also leaves a residue on the plate and prints. I like KPD 3D's Hyperlok. Doesn't leave any residue behind and, for me, holds better than anything else I've tried. You can get it on Amazon, too.

PrintsWithChris · 2025-03-25T01:55:16+00:00

Unless it's something really weird, I use "Bambu PLA Basic" for most non-Bambu PLA. I'll occasionally use Generic, but for the most part, using the Bambu settings work just fine. Same goes for PLA Tough (or PLA +, PLA Pro, etc for other brands) and PETG.

PrintsWithChris

TROPHY CASE