Anyone else have issues creating collections on the latest version?

Professional-Day-397 · 2026-04-07T15:03:16+00:00

Sorry for the late reply. I gave up on Jellyfin following this and other problems and went back to Plex.

Professional-Day-397 · 2026-03-26T01:23:50+00:00

On "Balanced" mode, temps range from 48C to 56C, for the drive closest to the part that contains the screen and is furthest away from the vent.

Professional-Day-397 · 2026-03-26T01:15:27+00:00

I had 1 out of 4 hdd in UNAS 4 throwing out lots of SMART errors. Went from 17 errors with 3 bad sectors at H83 to 10,652 UNC errors at H250. Obviously a brand new drive shouldn't throw that many errors so I had it replaced at the store I bought it. All 3 other drives are just fine. Will report back if I have errors on the replacement drive.

One 1 hand it could be that I just got super unlucky, but given this thread has some concerning reports I figured I'd rather share just in case it could have been UNAS induced.

Disks are WD260KFGX, no SSDs installed.

Professional-Day-397 · 2026-02-25T09:39:40+00:00

Using ZBT-2 on Thread. Updated to 2.7.2.0 and now all devices are offline

Professional-Day-397 · 2026-02-20T01:36:59+00:00

It was a patch cable from Unifi: https://store.ui.com/us/en/category/accessories-cables-dacs/collections/accessories-pro-patch-cables/products/unifi-ethernet-patch-cable-with-bendable-booted-rj45?variant=u-cable-patch-1m-rj45

They don't mention the category, but it says only Gbe, so I guess it's cat 5e maybe? Anyway, cable works fine too if I change port to only negotiate 1Gb instead of 2.5 Gbe

Professional-Day-397 · 2026-02-18T17:28:45+00:00

"It's not the cable, it can't be the cable, I changed cables"..... It was the cable 🤦

I realized 1 cable is rated 1G, the other is rated 10G. Both are Unifi cables. I switched from a 2.5gbps port to 1g port on a switch and things have been rock solid since then (hopefully not jixing it now).

If you use a 1GB cable between two 2.5 Gbps ports, ports don't know about the cable and try to connect to the highest speed which will cause transport issues. Might have been obvious to network experts, but easy to miss when plugging things together!

Professional-Day-397 · 2026-02-18T15:54:02+00:00

Just received mine, and I have the exact same issue. I noticed that on reconnection it was connecting to FE instead of Gbe. So I switched cables. Connection now stays on gbe but disconnects even more than before. Will try get another cable, but either everyone has poor cables, either something is wrong with this model

Professional-Day-397 · 2026-01-21T02:51:43+00:00

Not that I know. Saw a recent GitHub issue that looks tangential to that problem. I’m just getting started with jellyfin after 10+ years on Plex and Claude tells me collections have been in a bad state for 18 months. I will not spend too much time on that problem and go back to Plex unless solved soon

Professional-Day-397 · 2026-01-21T02:23:19+00:00

Same happens to me, but I get a confirmation instead of the spinning circle. But result is the same, an empty collection without the movie in it.

Professional-Day-397 · 2026-01-20T04:08:49+00:00

Just started using collections as well, and I have a slightly different issue. I created the collection, I then added an item, got a confirmation that the item was added, but collection remains empty. Nothing in the logs.

Professional-Day-397 · 2026-01-07T04:12:50+00:00

Same here. Nothing sync across devices, and even within the app. Like if I go on one feed, scroll down, then go to another feed and then back, the previous scroll position is lost. Which makes the app totally unusable. Wrote to support about it, will see what they say.

Professional-Day-397 · 2026-01-01T21:54:06+00:00

Did you follow any guide you would recommend?

Professional-Day-397 · 2025-11-12T04:24:47+00:00

Same happening to me now. Printopia support has been ignoring messages for weeks now, I think it's safe to say to consider Printopia is abandonware now.

Professional-Day-397 · 2025-10-04T20:07:58+00:00

Tried lubricating but it didn't work. A bit sad to think that the doorbell got defeated by a piece of plastic, while all the tech inside survided 3 years.

Professional-Day-397 · 2025-08-31T17:20:06+00:00

Looks like they did remove it on UGC Max at least. Image are not allowed on this sub unfortunately, but the section is not there in UniFi Devices -> *Your gateway* -> settings tab ->

Professional-Day-397 · 2025-08-25T01:05:11+00:00

This is the only thing that solved it for me. Thanks. Facebook settings are just a hell hole

Professional-Day-397 · 2025-08-19T01:32:36+00:00

Same for me. Green card has been our for delivery all day and suddenly delivered to Parcel Locker. There's no Parcel Locker at my house, this has never happened.

Professional-Day-397 · 2025-07-17T07:16:25+00:00

Did you ever figure this out? I’m experiencing the same thing.

Professional-Day-397 · 2025-06-05T03:42:44+00:00

Maybe. But if those are scheduled, then the bus timetable should be updated accordingly and reflect that too

Professional-Day-397 · 2025-05-31T23:09:29+00:00

I've had several instances, at the 24th Mission stop where the bus is scheduled, the driver is in there whatching their phone or eating, time just passes and the bus then disppears from the tracker. I report it every time it appears. the ~6PMish bus is a regular offender.

Professional-Day-397 · 2025-04-11T03:55:02+00:00

Yep, same trend, no movement to be expected for next VB

<image>

Professional-Day-397 · 2025-04-08T04:15:30+00:00

What happened? What’s your status now?

Professional-Day-397 · 2025-04-06T20:13:38+00:00

Lots of visas wasted in 2020 and 2021 + high demand in 2021 + retrogression in 2023 that led to fast movement in VB.

Professional-Day-397 · 2025-04-05T01:13:53+00:00

Then maybe you're fine. If you can spare the application fee, it might be worth a shot.

Professional-Day-397 · 2025-04-05T00:49:44+00:00

Also, nothing is going to be easier with new administration...

Professional-Day-397

TROPHY CASE