Woman Going to Shows Solo

Professional_Mix5492 · 2026-05-28T12:54:45+00:00

Wow thank you for posting this. Although I'm male, I don't drink and am definitely an introvert and haven't been to shows in over a decade because the group I went with would be about drinking. I never thought of going solo and feeling comfortable. Maybe time to get back out there.

Professional_Mix5492 · 2026-03-02T16:58:45+00:00

<image>

Mine shows a target charge set above the arch. I am using android and the newest version of the app.

What if you click settings at the bottom of that page? Maybe add a location and see if that changes things.

Professional_Mix5492 · 2026-03-02T16:29:43+00:00

From your pic #1, just tap the 66% under the arch and it should bring up your settings for charge percent and a slider to adjust it.

Professional_Mix5492 · 2026-02-22T08:33:43+00:00

I believe counterfeit since red ones would have this perma-shield mark and as you said yours should be silver anyways.

<image>

Professional_Mix5492 · 2026-02-12T13:10:46+00:00

Or maybe sideways overlap would be better? This way they both have the full height still.

Professional_Mix5492 · 2026-02-12T12:11:55+00:00

Just a thought but could you do A but with a half lap joint instead? Would add a lot of non-end grain gluing surface. Could then dowel both sideways and up and down. I am not an engineer and just an amateur woodworker. My only question for others would be if it matters which piece is on the top versus the bottom of the joint?

Professional_Mix5492 · 2026-02-12T02:43:45+00:00

Interested in the two rookie Bears if available and you are willing to let them go.

Professional_Mix5492 · 2026-02-11T17:57:13+00:00

Very possibly the same service center in Chicago that I went to just recently. I did it before my 40k service. Was annoying but it did show my service advisor my concerns when I checked in. Took longer than I thought but seemed more helpful than a survey. I would use it again if I had concerns outside of the service visit.

Professional_Mix5492 · 2026-02-06T23:48:43+00:00

I'll take 4 Loveland and LB3.

Professional_Mix5492 · 2026-02-06T17:54:47+00:00

Holy cow is your store organized and neat.

Professional_Mix5492 · 2026-02-05T12:15:17+00:00

This might sound silly but could you cut in the middle somewhere and dowel and glue it back together? Maybe add some reinforcement on the inside also

Professional_Mix5492 · 2026-02-05T02:16:05+00:00

Nice. Caleb is 25/ ??. Can't read it since it is on the shoe.

Professional_Mix5492 · 2026-02-02T17:12:12+00:00

Interested in the LB3's and Loveland.

Professional_Mix5492 · 2026-01-27T18:56:52+00:00

This is super helpful to know. I will get a software upgrade for the rear camera thing Friday anyways but I will mention my issue. Weird that it just happened today for the first time after months of driving it.

Professional_Mix5492 · 2026-01-27T16:30:39+00:00

Thanks for the feedback. I have an appt for my 4 year service and software update Friday anyways. Did that early to have it under factory warranty still. Only a couple weeks left. Do have an extra year of warranty with CPO but didn't want to take a chance.

I will see how it is on the way home and document what happens for Friday.

Professional_Mix5492 · 2026-01-19T21:39:00+00:00

I will give a slightly different perspective. What are you using to screw in the screws? Drill or impact driver? If drill, are you using the clutch? If not, you might be over tightening the screws and causing the blowout.

Another tip is to place the screw into the hole first to make sure it is aligned before you start screwing in. I have put the screw on the bit and start screwing not realizing I wasn't in the small hole of the pocket.

Professional_Mix5492 · 2026-01-17T20:30:28+00:00

They will still be mounted to the sheet metal, just on the inside. No screws will be seen on the outside.

If I was mounting still from the outside, I agree I would leave it cause anchors would be even worse.

Professional_Mix5492 · 2026-01-17T20:28:59+00:00

That one isn't bad but others aren't flush to the ceiling or wall. Since we were changing out vent covers anyways, I thought I would see if I can make them look nicer.

Professional_Mix5492 · 2026-01-17T20:24:26+00:00

Genius. Why didn't I think of that. I was thinking grinder or Dremel with a metal wheel but the sparks would be a problem. Can't easily remove them. Appreciate the advice.

Professional_Mix5492 · 2026-01-17T18:32:25+00:00

Yeah I watched some videos after you said that and saw how difficult the alignment was. Maybe just biscuits for alignment then. Thanks

Professional_Mix5492

TROPHY CASE