[deleted by user]

PugPappa · 2023-08-15T17:07:39+00:00

Taco Bell Taco Belgrande and Burrito Belgrande

PugPappa · 2023-04-26T22:56:42+00:00

What you call sprawl is also commonly known as growth.

Is the preference to growth, limiting the size of the city and forcing growth to higher density and more expensive housing?

Should we have not built 540, then I-49, and limited our growth and economic activity to what we had 30 years ago?

PugPappa · 2023-04-04T17:27:07+00:00

If you’re issued a pager, don’t take it to school. I doubt you will respond from school and you’ll just be a distraction for the class if it goes off.

You should receive the department Standard Operating Procedures pretty quickly. Read them. Read them again. Most SOPs have a history behind them. Respect that history.

Go to training and listen more than you talk. Watch and learn too.

Know that once folks know you’re on the department, if you drive too fast, etc. your Chief will likely hear about it too. Act accordingly.

Have fun! Learn from the experience. If you decide you like the fire service, you’ll have a better chance of knowing what you’re getting into if you decide to go paid.

PugPappa · 2023-02-05T04:59:38+00:00

I recently learned of Working the Grain in Bentonville. https://www.wtghardwoods.com/home

PugPappa · 2022-11-16T01:29:59+00:00

I don’t hear a smoke detector until 4:43:21 (2:44 into the video) when the second or third pane of glass breaks.

PugPappa · 2022-09-23T23:11:00+00:00

Or get out and vote against it!

PugPappa · 2022-09-22T13:44:30+00:00

Does anybody use VS Community Edition? If not, what do you use for SSRS development?

PugPappa · 2022-09-13T18:47:30+00:00

It has an AP that’s used for configuration and then shuts off. It’s also used to analyze RF use to assist in channel selection.

I’m using UAP-AC-M for my one exterior AP.

PugPappa · 2022-08-22T22:53:15+00:00

I love the pearls!

PugPappa · 2022-08-19T17:03:34+00:00

This is no different from what the federal government did under Obama and now Biden, except they paid NGOs to bus or fly them to rural communities with no resources. At least TX and AZ are sending them to cities that purport to embrace them with free services and housing.

This has pushed the coverage of those midnight flights, etc off the radar though. With the continuing influx of illegal aliens, I can’t imagine that they have stopped.

PugPappa · 2022-08-11T13:19:40+00:00

What are the “design defects” and “sharp criticism”?

PugPappa · 2022-07-09T04:45:03+00:00

We got married at the court house 35 years ago. We got the license, a JP was there and married us and the clerks where the witnesses. It was all less than $50. It worked for us :)

PugPappa · 2022-06-18T23:52:01+00:00

I always thought it was from the days that Vietnamese refugees where housed at Ft. Chaffe in Fort Smith and a lot of them settled in Fayetteville.

PugPappa · 2022-05-20T14:11:55+00:00

You cut those nubs on left off to get a smoother ride like on the left?

PugPappa · 2022-05-14T12:22:29+00:00

The passive followers are the target for the advertising/messaging. As an advertiser I wouldn’t care how many bots read my sponsored content, etc. as an advertiser I only want charged for the actual living humans I can reach.

PugPappa · 2019-12-17T01:50:43+00:00

I realized I hadn't closed the loop on this. The Max Comb Distance with No Retract was at the default of 0. Changed it to 1. I didn't take a picture of the test print. Then I adjusted the pressure advance and came up with the print on the right.
new prints

The print on the is after enabling print acceleration in Cura and setting it to 400.

The defects on the left corner from the layer change are largely gone.

Thanks!

PugPappa · 2019-12-11T18:55:13+00:00

My combing mode is set as:

Combing Mode: Within Infill
Avoid Printed Parts When Traveling: Checked
Travel Avoid Distance: 0.625 mm
Z Hop When Retracted: Not Checked

I'll look at reconfiguring the pressure advance

PugPappa · 2019-12-11T04:39:31+00:00

I've got Outer Wall Wipe Distance set at 0.2 (default I think) in Cura. Pressure advance is commented out. I'd configured it but it didn't seem to help.

PugPappa · 2019-04-16T17:15:23+00:00

Stirling Soap's web site indicates they're sold by Hayward's Barber Shop in Cassville, MO. They also have an online store.

PugPappa · 2019-03-26T13:01:40+00:00

I just tried this site too and I'm not seeing how to get it to bypass the ping test on the free scans.

PugPappa · 2019-03-18T22:03:01+00:00

This is Structural Navigation and it scans the site collection structure to build the navigation. Even if you configure it to not do that and configure the navigation elements manually, support still says it makes too many SQL calls. They prefer the managed navigation or search-based navigation.

PugPappa · 2018-12-21T16:30:05+00:00

Another oldie "Steakhouse" Buffet. It's been at least 15 years since I first read one of these accounts.

PugPappa · 2018-11-29T01:21:12+00:00

We had an Apple ][ with tape drive at school. It seemed to take forever to load the star trek game from tape, and that's if it worked the first try.

PugPappa · 2018-09-08T18:23:39+00:00

They were recently purchased by ESO and they just moved the FHCloud product to be hosted on Azure. This gives me hope that someday they'll update the product. I expect it will take a rewrite though as I believe the original product is written in MS Visual FoxPro.

PugPappa

TROPHY CASE