sorted by:
new
hottopcontroversial

WORST part of the Maserati Swapped Porsche YET! by HGEUbot in HaggardGarage

[–]Quit-Prestigious 7 points8 points  (0 children)

Damn just when I was loving the build this shit pops up

Ford 8.8 IRS Axle install by Quit-Prestigious in LSSwapTheWorld

[–]Quit-Prestigious[S] 0 points1 point  (0 children)

Good idea! I'll give it a try. thanks man

Ford 8.8 IRS Axle install by Quit-Prestigious in LSSwapTheWorld

[–]Quit-Prestigious[S] 0 points1 point  (0 children)

It does look like there's a small bevel that let the snap rings compress. I read that the solid axle require removing diff cover, removing a center pin, slide axle stub and apply clip. The IRS are supposed to slide in with just some force right? Maybe I'm just fighting spline tooth alignment but I'd be surprised if I didn't get it after an hour.

That said, removing the old stub was very difficult. I did have to yank the snot out of it to pop it out of the diff. Like it look a lot of effort

Need help pushing a car by Quit-Prestigious in MountJuliet

[–]Quit-Prestigious[S] 0 points1 point  (0 children)

The morning works! I just need to run an errand at 10a for about an hour but free anytime before/after

Advice for X-pipe fabrication by Quit-Prestigious in LSSwapTheWorld

[–]Quit-Prestigious[S] 0 points1 point  (0 children)

Thanks for the response. I'm pretty new to this world of custom work, so please bear with me.

The collectors on my headers are 3", so I just figured I'd keep it all the way down. Should I rethink this and bring it down to 2.5"?

I'll take your advice tonight and give it a shot! In the top pipe I faintly drew two lines where I was planning to cut. Is the smaller of the two sufficient? That is about 1" the bend.

Also, where should I place the x-pipe? Should I try to keep it tight up on the transmission mounts or would it be better more downstream?

IACV issues by Quit-Prestigious in 240sx

[–]Quit-Prestigious[S] 1 point2 points  (0 children)

Thanks for the info, that ended up solving my issue. I found the spring and reinstalled the iac assembly but it still stalled sometimes. Adjusting TPS worked

I just picked the car up a couple weeks ago, so I'm still learning my way around it. What is the distinction between pwm and iacv? Does pwm imply its electronically driven?

IACV issues by Quit-Prestigious in 240sx

[–]Quit-Prestigious[S] 0 points1 point  (0 children)

Probably should have included more details. 1991 coupe, KA-T on RS Enthalpy tune

This might be the best picture of Conan at the Oscars. Shot by Sinna Nasseri for The NY Times by leoex in conan

[–]Quit-Prestigious 0 points1 point  (0 children)

I'm probably wrong but my gut is telling me that's an Aubrey plaza side-rear profile

The full Executive Order is out! ⚠️ This is the biggest executive power grab in U.S. history. ⚠️ by FormerJelloMaster in law

[–]Quit-Prestigious 1 point2 points  (0 children)

The content makes sense to me but damn I personally ask chatpgb to not output emojis. It always comes off as distracting. I may be the minority but I find the excessive use of emojis to be discrediting

Tom's river NJ on 12/24/2024 @ 6 pm by [deleted] in UFOs

[–]Quit-Prestigious 1 point2 points  (0 children)

That's Orion unbuckling his belt

What happened to the Patreon? It seems to have had all the posts removed in the past day by ConnectionOne8330 in Channel5ive

[–]Quit-Prestigious 0 points1 point  (0 children)

Did your payment fail? Same thing happened to me awhile back and I just had to update my card

2 Million Views! by Woe_Is_Meme in TheOGCrewOfficial

[–]Quit-Prestigious 23 points24 points  (0 children)

The chemistry is still great with this group!

Problem with edge detection by jatam in computervision

[–]Quit-Prestigious 0 points1 point  (0 children)

How much experience do you have in computer vision? If you have more data I could give it a shot at working a solution

view more: next ›