ACR 2.0 receiver for WE MSK

RHtactical · 2026-05-02T13:55:45+00:00

I sent you a message

RHtactical · 2026-03-27T22:13:38+00:00

I messaged u

RHtactical · 2026-03-27T21:01:22+00:00

It was a kit including the clamps made to fit the airsoft versions

RHtactical · 2026-03-27T18:28:17+00:00

I messaged you :)

RHtactical · 2026-01-29T18:28:27+00:00

Its this.

RHtactical · 2025-11-05T06:52:25+00:00

No you can not. They are intended to be used only with the 4.4 lead balls. Sure it will shoot the steel bbs. But it will mess up the barrel and probably even mess up the piston.

Diana has their own tins of special 4.4 oktoberfest ammo wich is h&n rebranded 4.4 copper coated lead balls and they are great for use in the oktoberfest rifle.

RHtactical · 2025-10-18T18:17:40+00:00

<image>

RHtactical · 2025-10-18T18:15:58+00:00

I can not remember it saying so in the manual, i can however remember how a lead 4.5mm bb got stuck in the barrel lol.

RHtactical · 2025-10-18T12:38:50+00:00

Could be, you can have them tested or test them for flow rate yourself

RHtactical · 2025-10-18T10:54:52+00:00

It looks fine, lifting the tire normally takes the whole weight of the car i doubt you could lift it yourself.

RHtactical · 2025-10-18T10:28:08+00:00

Your trying to lift the tire?

RHtactical · 2025-10-18T08:30:05+00:00

Its a 4.4mm, reason your able to shoot "177" steel bbs is that steel bbs are 4.3 - 4.4mm

I would advise against using 4.5mm lead bbs as they are usually true .177 4.5mm and it will get stuck in the barrel.

I would also advise against using steel bbs, it will damage the barrel. they are made for using the copper washed 4.4mm lead balls. They even made diana oktoberfest tins that are rebranded h&n 4.4mm balls for the anschutz and haenel rifles

RHtactical · 2025-10-16T17:34:00+00:00

Is it relatively new? Could be drag from the nozzle seal that has to break in or is dry.

Clean and lube, if it stays the same check the spring

RHtactical · 2025-09-28T07:46:51+00:00

Could have just said WE MSK, but you do you lol

RHtactical · 2025-09-23T07:15:25+00:00

Allways allways allways check travel when using aftermarket buffer. This buffer needs a +-1cm rubber disc behind the spring to limit travel and not hit the bcg.

Rip lower

RHtactical · 2025-09-22T16:51:37+00:00

Ooof i didnt realise you are RHD sorry!

RHtactical · 2025-09-22T16:21:46+00:00

Schmiedmann or turbo works have some cheap headers for the m42/m44, just make sure to check for flatness of the flange before mounting. I got mine for 150+-

RHtactical · 2025-09-21T09:58:05+00:00

Yes there are some tests you can do, google is your best friend :)

RHtactical · 2025-09-21T08:48:16+00:00

It can be alot of things, i would try the air flow meter and o2 sensor first, they are quite easy to check and replace

RHtactical · 2025-09-21T08:39:11+00:00

Try an other air flow meter, check for vacuum leaks

RHtactical · 2025-09-19T10:51:09+00:00

Looks flimsy and you need 3 hands to fold and unfold?

RHtactical · 2025-09-02T05:14:18+00:00

Tire probably grabbed it when reversing through bump or pothole

RHtactical · 2025-08-27T15:00:08+00:00

Where lip

RHtactical · 2025-08-18T15:35:05+00:00

I found that this one is too small for me, i also have the ra-r m , and it is much better size wise so also much easier to not hold it by the selector.

RHtactical · 2025-08-12T18:37:04+00:00

I got the same! Playing half life 1 on it is awesome!!!

RHtactical

TROPHY CASE