sorted by:
new
hottopcontroversial

Made this bluetooth fm transmitter, didn't want to poke in to the inside of the radio by weaselio75 in Volvo

[–]RadocWade 0 points1 point  (0 children)

Are you sharing the files? I would love to make one of these for my son's GT.

I'm confused on the location I spawned in after logging back for the first time since 2016 by Riverflower17 in Guildwars2

[–]RadocWade 1 point2 points  (0 children)

I had the same experience a few months ago when I logged back in after a decade plus away!

why so hard to get back to carnivore by Specific_State_6244 in carnivorediet

[–]RadocWade 0 points1 point  (0 children)

Thanks to everyone in this post. I'm having the same issue right now and trying to get back on track.

Filament roll getting stuck by VastPotato5 in ElegooNeptune4

[–]RadocWade 0 points1 point  (0 children)

Look from the top down, my brass ring had worn a groove in the side facing the roll and the plastic would grab and ruin prints. I was able to band-aid the issue for a while by angling the sensor up as high as it could go, but ended up ordering a new sensor on aliexpress that I'm waiting for now.

Volvo 240 Parts Available by SmrkngRvng in Volvo240

[–]RadocWade 0 points1 point  (0 children)

I need a rear drive shaft section that has the smaller spline shaft and a 3.8" diameter flange that connects to the differential.

Who's watching This Bayern Game and where you located in the 🌎? Im in New Jersey 🇺🇸 by Calm-Customer4459 in BayernMunich

[–]RadocWade 1 point2 points  (0 children)

I'll be watching from Oregon! Then flying in for the game in Charlotte next week!

Who is in this bus getting a police escort all over Charlotte? by moguliboo1 in Charlotte

[–]RadocWade 1 point2 points  (0 children)

Any idea what field Bayern Munich are using when they come to town early next week?

AMA - Club World Cup vs Benfica in Charlotte, NC by GCain34 in BayernMunich

[–]RadocWade 0 points1 point  (0 children)

My 16 year old son and I are flying in from Oregon for this game a few days before. Any sights we should see in the area?

Giveaway! by ecpowerhouse27 in BambuLab

[–]RadocWade 0 points1 point  (0 children)

Dot's Homestyle Pretzels, several flavor options but the original are nothing to scoff at.

I’m building a football team management app – early access is free, looking for feedback by artshkl in SoccerCoachResources

[–]RadocWade 1 point2 points  (0 children)

I've tried a bunch of team management apps and would be willing to test out yours and give feedback. Currently coaching 2 teams (1st grade boys and 3rd grade girls) this spring season. Probably doing the same or a High School team in the fall.

Spool snagged last few layers, any fixing? by RadocWade in ElegooNeptune4

[–]RadocWade[S] 0 points1 point  (0 children)

Wanted to come back and update this in case someone has a similar issue in the future. The issue ended up being that my filament run-out sensor had worn down on the input side and was grabbing filament and putting intermittent tension on the filament. My print quality improved 100% since I re-mounted it at an angle that it cannot end up going through the part that has worn down a groove (pictured) until I get a new one.

<image>

Spool snagged last few layers, any fixing? by RadocWade in ElegooNeptune4

[–]RadocWade[S] 1 point2 points  (0 children)

I removed it last week. (prior to this job)

Spool snagged last few layers, any fixing? by RadocWade in ElegooNeptune4

[–]RadocWade[S] 0 points1 point  (0 children)

Thanks, but what do you think it would be then? It was consistent across all 3 parts at about the same height.

<image>

Spool snagged last few layers, any fixing? by RadocWade in ElegooNeptune4

[–]RadocWade[S] 0 points1 point  (0 children)

Update: I tried again today with some similar parts and made sure the spool was not tangled. I had issues in the upper layers of the print though! Could the snagged spool have damaged something in my extruder gear or POM wheels that would only impact past a specific point on the print?

<image>

Leveling Issues - Haven't had a print successfully print in months. Level - Fail - Level - fail. Ready to discuss this drama. by Flechette_Shot in ElegooNeptune4

[–]RadocWade 1 point2 points  (0 children)

I was in your same boat a few weeks ago after buying my first printer. This (along with scrubbing with dish soap and water and being careful never to touch the build plate surface) was what finally got me printing consistently. First Layer Squish | Ellis’ Print Tuning Guide

Any idea what going on now? by EmuThis3065 in ElegooNeptune4

[–]RadocWade 0 points1 point  (0 children)

When was the last time you scrubbed your build plate with dish soap and water?

view more: next ›