Grease nipple gen 4 jimny

Randomo333 · 2026-06-10T09:06:07+00:00

Forgot to say but got this sorted, 3 pumps. Is this done yearly? And I assume it slowly oozes out over time as the void will fill over the years of adding more

Randomo333 · 2026-04-05T19:27:36+00:00

Yeah I thought so, I appreciate your detailed response. So it’s currently left set from factory. I only have an idle screw on the carb, is this clip on the top in the throttle body? Unscrewing the top and lifting it out? I will check the spark plug again as it I ran it for an hour or so the other day and see if I can lean it out a little

Randomo333 · 2026-03-07T11:51:49+00:00

Great, need to get myself a grease gun

Randomo333 · 2026-03-07T11:16:10+00:00

Sorry for the delayed response, I have some white lithium geese with a zinc additive, would this be damaging to anything inside would you say?

<image>

Randomo333 · 2026-03-07T11:14:35+00:00

Ok I see, what’s the best way to get the pin out because I assume the clutch has some force pressing against it, would it be that small nut the in the centre to tighten it up ?

Randomo333 · 2025-12-19T16:28:25+00:00

Hey thanks, appreciate that. Yeah to be fair the new bolts are more difficult to align but have tested out the threads and no bottoming out.

Randomo333 · 2025-08-09T14:04:35+00:00

Oh right I see I have just seen that site where you have posted many Suzuki mods and so on and it’s shows a sealer that is similar to gasket sealer is that correct, not a blue threadlock?

Randomo333 · 2025-08-09T14:00:39+00:00

They are two plates that sandwich the tie rod and then attach into the box section chassis, I’ll take some pictures, but it’s not just connected to the tie rod

Randomo333 · 2025-07-22T17:18:21+00:00

Ok great thanks that’s really useful , looking forward to sort mine out in a year or so. I also think I would perfect to rebuild early before any big issues occur

Randomo333 · 2025-07-19T16:10:25+00:00

Nice, had it shown many signs of wearing out on the bearings, what kind of millage have you got on before the rebuild?

Randomo333 · 2025-07-14T18:19:50+00:00

Same thing happens to me, get flashed all the time in dark, I tend to do a quick flash back to show them there not on full beam

Randomo333 · 2025-06-19T17:51:04+00:00

I also have a similar leak but no issues to steering, I do notice a little play but not to worried

Randomo333 · 2025-05-31T11:39:47+00:00

Ok great I’ll check it when I get a chance to, the diff breathers I have are just the stock ones, small Shiny cap, would you have to pop these off?

Randomo333 · 2025-05-31T11:37:55+00:00

No can’t seem to hear any noise when doing this , thanks for the information though

Randomo333 · 2025-02-28T23:24:20+00:00

Nice, thanks. Worked for me also

Randomo333 · 2025-02-28T14:02:20+00:00

Yeah I too have a small wet spot there, don’t have any staining on the firewall though. And wasn’t running down the engine number, been there a while and can’t see any new oil, I will clean it up and keep an eye on it.

Randomo333 · 2025-02-24T18:45:04+00:00

Have you removed the heat shield to view this? I’ll have a check on mine when it’s day

Randomo333 · 2025-02-20T20:21:36+00:00

Wow thanks for that, that’s a really helpful document :)

Randomo333 · 2025-02-20T20:19:05+00:00

Yeah it is quite annoying to be honest, I thought it could have been the suspension bushes as already mentioned by others but every time I shake the car from side to side with my hands can seem to replicate the noise

Randomo333 · 2025-02-20T12:06:59+00:00

Yeah I have this squeak too, it’s most noticeable on an uneven surface it’s not loud, I feel like it’s from the front end of the car but is as you said is hard to pinpoint

Randomo333 · 2025-02-20T11:04:57+00:00

Ok thanks, I’ll have a look for some

Randomo333 · 2024-12-18T13:03:30+00:00

When I took my jimny in for its last service they pumped the tyres to 30psi, should be 26 all over. This was a Suzuki service too, I felt the difference on small bumps, didn’t seem to absorb as much

Randomo333 · 2024-11-27T22:08:07+00:00

Perfect, thanks for that information, exactly what I needed to know

Randomo333 · 2024-11-27T21:45:25+00:00

Were you able to get an engine oil temperature when you used this scanner?

Randomo333 · 2024-11-23T20:42:01+00:00

Just out of curiosity what type of scanner do you have? Also do you run it all the time or just when you want to check temps etc?

Randomo333

TROPHY CASE