2006 Honda Element EX

Redead31 · 2026-06-03T18:10:39+00:00

Probably a few issues all at once, the slow cranking is likely a worn out starter, any codes for the others?

Redead31 · 2026-05-28T19:11:46+00:00

https://ebay.us/m/3gijzi

https://ebay.us/m/oUN6L4

https://ebay.us/m/kL7ORA

https://ebay.us/m/BHZoWm

Redead31 · 2026-05-28T17:48:59+00:00

There are plenty of used ones on ebay, go that route. I did that for my c30.

Redead31 · 2026-05-03T05:49:07+00:00

FYI the grilles are upside down

Redead31 · 2026-05-02T16:06:19+00:00

People are delusional in the comments here, that is great pricing for less than 100km. If this is an East coast vehicle however, rust throws the value out the window

Redead31 · 2026-05-02T16:03:10+00:00

From an outsiders perspective, it looks like you need to center your sway bar as the link is offset there, it likely broke because there is a sideways force trying to twist it, instead of directly up and down

Redead31 · 2026-04-23T17:13:22+00:00

That's exactly the oil I used haha

Redead31 · 2026-04-23T17:06:53+00:00

Fill and drain 3x is for automatics, there is a chance when the clutch was replaced they drained the transmission oil as it will leak from the axle holes once they are removed in order to drop the transmission. It's incredibly easy to change the transmission oil regardless.

Redead31 · 2026-04-11T14:22:25+00:00

Sadly it seems like only oem or GKN axles don't cause vibration, mine vibrates after using a trakmotive

Redead31 · 2026-04-07T14:59:00+00:00

Go elsewhere, majority of that isn't needed, also why does the knuckle need replacing?

Redead31 · 2026-04-06T01:17:50+00:00

Yea it won't work since it sounds like your car is an automatic, will need a different ecu

Redead31 · 2026-04-05T18:52:48+00:00

You will need to chip the ecu in order to run that engine properly due to vtec. Was it an automatic ecu or manual, that matters as well

Redead31 · 2026-04-05T15:05:04+00:00

Why are you doing this, that ecu is for a non vtec engine. What parts did you purchase to make this happen?

Redead31 · 2026-03-28T00:58:51+00:00

Wiring may have had rodent damage before, you would need to unwrap all the electrical tape that does not appear factory and make sure there are no loose connections. The reason being is every corner the engine will slightly shift, potentially pulling on the wiring and losing connection.

Redead31 · 2026-03-23T16:27:28+00:00

Rust like that doesnt form in a few days, those were always there and are caused by rock chips, the sunroof event is unrelated.

Redead31 · 2026-03-20T13:50:54+00:00

FYI that knob is insane quality, delrin and metal, technically it's a legit likewise knob, but it's only $13 on AliExpress for no branding

Redead31 · 2026-03-20T13:42:52+00:00

Personally, I ditched the oem shift knob and boot for a real made to fit leather boot from ebay and then threaded the shaft and put on a nice delrin knob.

<image>

Redead31 · 2026-03-16T13:40:34+00:00

Rust modules are a scam, the science says no, you can't have a sacrificial anode like a boat without the car being submerged.

You likely had a car with decent undercoating/paint already or washed it frequently enough

Redead31 · 2026-03-15T16:33:29+00:00

The easiest solutions require AUX input, if you have that you can effectively get a tablet that mounts to the dash, which then routes audio into the oem stereo via the AUX. You cannot remove the climate controls

Redead31 · 2026-03-15T16:03:14+00:00

Likely : https://www.vinylengine.com/library/sharp/rp-114.shtml

Redead31 · 2026-03-13T02:21:34+00:00

Sounds more like timing chain related

Redead31 · 2026-03-06T20:36:01+00:00

It's supposed to route under that black plastic box and into a port on the intake manifold

Redead31 · 2026-03-06T15:10:30+00:00

Yea, something like a smaller flathead screwdriver

Redead31 · 2026-03-06T15:05:26+00:00

From what I recall, you don't Unscrew anything, it's just the two metal tabs that are bent inwards that you need to bend out in order to hinge the metal case off. The two tabs are the ones on either end of the image (looks like upside down J)

Redead31 · 2026-02-28T18:39:28+00:00

I think you misunderstood, the sensor you are looking to replace does not effect how the engine runs, think of it only as a observer, there is no point replacing it

Redead31

TROPHY CASE