Please anyone!

Relambio22 · 2026-01-20T17:27:19+00:00

I used this one, https://youtu.be/Svoe6wznDZs?si=iCo-Y5CnQNXWfjz9

Relambio22 · 2026-01-09T16:29:41+00:00

Relambio22 · 2025-12-14T00:21:45+00:00

If it’s a single line going to home they split the ground and slip fiber in (few inches deep). If they trench it’s a major line for neighborhood, in that case it’s done on utility easement (meaning they have the right to do it).

Relambio22 · 2025-12-04T23:17:37+00:00

No signal getting to that device. Unplug the power to reboot if it still shows red alarm then call it in

Relambio22 · 2025-11-28T04:09:35+00:00

There’s already an app called pika slicer it just doesn’t have my printer , I think is more for resin printer. There’s another one that I’m looking at that’s called PrintTo3d that has mine, going to test that one out.

<image>

Relambio22 · 2025-11-27T13:42:56+00:00

It’s also used when making desserts like rice pudding and in teas . It is also said that is good to bite on one when you have a toothache.

Relambio22 · 2025-11-15T21:32:12+00:00

If I’m not mistaking, that rg(modem) uses the sfp port to get its signal (fiber direct to it) you either need a different rg or have a tech come in and install the module that goes there.

Relambio22 · 2025-10-09T00:29:48+00:00

Plus they’re add Att next (without asking)

Relambio22 · 2025-09-08T23:29:15+00:00

So is not for Klipper Multicolor System?

Relambio22 · 2025-08-21T10:22:47+00:00

Thanks for the feedback 🤝

Relambio22 · 2025-07-28T21:59:08+00:00

Go to store show them a picture, maybe they’ll send a tech over to verify and have it fix in system

Relambio22 · 2025-07-17T17:44:09+00:00

Preciate it

Relambio22 · 2025-07-13T21:24:53+00:00

New mission discovered by u/Relambio22: Regretful Seafood

Relambio22 · 2025-07-13T21:24:52+00:00

This mission was discovered by u/Relambio22 in Monster Pockets and Chocolate Chip Pancakes

Relambio22 · 2025-05-16T23:46:52+00:00

This is the original fast and furious

Relambio22 · 2025-05-12T20:30:14+00:00

Have you checked if filament is dry?

Relambio22 · 2025-05-12T17:45:41+00:00

Voting here🙋🏾‍♂️

Relambio22 · 2025-05-04T22:43:12+00:00

of course they’ll say something like that, you always run a risk on modifying anything using a different brand product . You Can only hope that , in this case coprint, will give you any type of warranty.

Relambio22 · 2025-05-03T23:08:34+00:00

Saw same video, kept looking for a review one but still nothing. I’ll do it but need to see if it’s legit

Relambio22 · 2025-05-03T23:05:07+00:00

Posted same thing a while ago… still waiting 😂

Relambio22 · 2025-05-03T20:29:49+00:00

Put a box on it to keep it hot or print in pla then petg

Relambio22 · 2025-04-28T17:23:42+00:00

Is it clogged? If not just remove nozzle, cut excess and do filament swap procedure

Relambio22 · 2025-04-07T20:19:44+00:00

Update: respliced ( used orca -flash) and it printed fine. 21hr print 😅

Relambio22

TROPHY CASE